Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Machine elements
1
Gear selection switch
2
Guard handle
3
ON/OFF switch with electronics
4
Button for starting lockout
5
Ventilation slits
Technical data
Rated power/Current consumption:
Voltage:
Gears:
Rpm under load:
Recommended mixing tool Ø:
Sound pressure level acc.to EN 50144:
Noise emission level acc.to EN 50144:
Hand-arm vibration:
Protection class:
Supplementary safety instructions
To be able to use the machine safely it is essential that you read these safety instructions thoroughly and
comply with all of them. The machine may be used only by people who are familiar with the operating
instructions and the regulations in force concerning work safety and accident prevention.
In addition, also comply with the general safety instructions also included with the machine.
Take care to ensure that the current voltage indicated on the rating plate corresponds to that of the mains power supply.
Do not use the device in any environments with potentially explosive atmospheres. Do not mix any solvents or solvent-
containing substances with a flash point of below 21° C.
Do not wind cables or leads around any parts of the body.
Use only cables approved for outdoor use. Never use the machine with a damaged cable.
Start up and run down the machine in the mixing container only. Ensure that the mixing container is stood in a firm and
secure position.
Do not reach into the mixing container with your hands or insert any other objects into it while mixing is in progress.
If the sound pressure level should exceed 85 dB (A) where you are working, use ear protection! We recommend that you
wear work gloves and protective goggles when using the mixer. Regulations require that you wear close-fitting
clothing.
Dust developing during the mixing prodedure is harmful to one's health. Wear a dust protection mask.
Intendend use
The machine is designed for mixing liquid and powder-based building products such as paints, mortar, adhesives, plaster
and similar substances in the construction business. Use the right mixing tool for the consistency of the material and
the quantity to be mixed. Please refer to the information in the technical data when choosing the size of mixing tool
(diameter).
This machine may not be used for the mixing of food stuffs.
The machine is not suitable for mixing of materials containing graphite powder, hydrochloric solutions or liquid manure.
Mixing such materials can damage or destroy the machine.
Before using for the first time
Screw the mixing tool with a size M14 male thread (9) firmly into the mixing shaft (8). To do this you will require two SW 24
open-ended wrenches. Place one open-ended wrench on the mixing shaft and the other on the hexagonal holding fixture
and tighten. To release or change the mixing tools, follow this sequence in reverse order.
Connect the machine to the 230 volt mains power supply. 230 volt devices can also be used with a 220 volt supply.
6
Fastening screws for the guard handle
7
Neck of the machine
8
Mixing shaft with M14 female thread
9
Mixing tool
CX 10-A
CX 20-A
1000 W/4,4A
1000 W/4,4A
230 V
230 V
1
2
0 - 670 min -1
0 - 400 min -1
0 - 700 min -1
Ø 120 mm
Ø 120 mm
84 dB(A)
84 dB(A)
97 dB(A)
97 dB(A)
< 2,5m 2
< 2,5m 2
/II
CX 40-C
1300 W/6,0A
230 V
2
0 - 500 min -1
0 - 850 min -1
Ø 140 mm
85 dB(A)
96 dB(A)
< 2,5m 2
/II
/II
CX 60-C
1600 W/7,1A
230 V
2
0 - 420 min -1
0 - 630 min -1
Ø 160 mm
89 dB(A)
99 dB(A)
<2,5m 2
/II
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
