Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1.
Safety Notice
· Before using the Storchenmühle Starlight SP, S t a r l i gh t Pro , please read the instructions carefully.
· Regardless of whether it is being used for age group I or II+III, ensure that the belt position is correct
at the load-bearing points. The buckle must always be below the belt guide (fig. 1).
· The child seat is only suitable for use in vehicles if the vehicle is authorised and fitted with three-point
seatbelts approved under UN - ECE Regulation No. 16 or other comparable standards.
· The child seat should always be fitted in accordance with the instructions, even when not in use. In the
event that the driver has to brake hard in an emergency, an unattached seat may cause injury to other
occupants in the vehicle.
· The child seat is only approved for use for weight classes I-IIII (9 - 36kg). The seat should only be
installed facing in the direction of travel.
· For weight class I (9 - 18 kg), the child seat must only be used with the integrated restraint system.
· Install the child seat in the vehicle in such a way that it is not clamped by the front seats or the vehicle
door.
· The child seat must not be modified in any way, and the instructions for installation and use must be
followed carefully, otherwise your child could be put at risk while travelling.
· The belts must not be twisted or trapped and must be completely tightened.
· IMPORTANT: Ensure that the lap belts in particular are tight and fitted as low as possible across the
child's pelvis.
· After an accident, the child seat must be removed and tested in the factory and, if necessary, replaced.
· Very bulky items of clothing must be removed prior to securing the child in.
· Always ensure that items of luggage and other objects are adequately secured, particularly those on
the parcel shelf, as these could cause injury in the event of a collision.
· Always set a good example and always use your seat belt. An adult who is not wearing a seatbelt can
also endanger your child.
· Notice: Only original accessories or replacement parts may be used.
· Never leave your child unattended.
· Always strap your child in.
· Protect the child seat from direct sunlight in order to avoid your child being burnt by it and to preserve
the color of the cover.
· The child seat must not be used without the cover. The cover must never be replaced with a cover
which has not been recommended by the manufacturer, since this cover comprises an integral part of
the seat safety system.
2.
Use of the child seat for infants (from 9 - 18kg · ECE-Group I)
2.1 Installation of the child seat using the three-point seatbelt
· Open the belt clamp. To do this operate the lever on the outside (1). The belt clamp will then open of its
own accord (2) (fig. 2).
· Extend the three-point belt, lift the head rest cover and feed the belt through behind the cover (fig. 3).
· Fasten the buckle so that you hear an audible click, and feed the lap section of the three-point seatbelt
past the red belt tensioners into the rear guides (fig. 4).
· First tighten the lap belt (1) and then the diagonal belt (2) (fig. 5).
· Place the diagonal belt in the belt clamp (3) and close the clamp (4) with an audible click. (5) (fig. 6).
· Next tighten the belt once more in order to ensure that the child seat is held as firmly as possible. For
this, simply pull the belt away from the belt clamp towards the vehicle seatbelt tensioner, and then
tighten the lap and diagonal belts accordingly.
2.2 Securing the child in
· To lengthen the straps press down on the central adjustment button (1), keep it pressed down and pull
downwards on the shoulder straps (2) (fig. 7).
· Open the buckle by pressing the red button in the direction indicated by the arrow (fig. 8).
10
· Place the straps to the sides (fig. 9).
· Place your child in the seat and put the child's arms through the shoulder straps (fig. 10).
· Fasten the buckle by pushing the two tongues into one another (1) and inserting them into the
buckle until it closes with an audible click (2) (fig. 11).
· Tighten the straps by pulling the central belt in the direction indicated by the arrow. The straps
should fit tightly to your child (fig. 12).
2.3 Adjusting the harness height
· Loosen the harness system.
· Pull on the ratchet stop button and raise the headrest to the next position (fig. 13).
NOTICE: Before adjusting the headrest, check if the insert cushion needs to be removed for the child
first. In the event of the insert cushion being removed, take care when feeding the buckle and crotch
pad through.
· The shoulder straps should always be positioned as shown (fig. 14). The straps should never follow a
course below the child's shoulders.
2.4 Adjusting the recline position
The child seat can be placed in a recline position by turning the adjuster handle in the direction
indicated by the arrow (fig. 15).
NOTICE: Once the internal harness system has been removed (for use for group II and up), the recline
position should no longer be used.
3.
Use of the child seat for older children (from 15 - 36kg · ECE-Group II-III)
Although the approvals standard for child car seats permits use of the Storchenmühle Starlight SP,
Starlight Pro with the vehicle seatbelt for children weighing over 15 kg, we recommend
continuing to use the integrated harness system until your child has reached a weight of 18 kg.
3.1 Before installation
· Please keep any parts removed in a safe place for later use!
· Loosen the harness and detach the shoulder strap loops from the metal connector (fig. 16,17).
NOTICE: The central belt, that means the belt-part with the metal connector (fig. 17), has to remain
on the child seat.
· Remove the shoulder straps by pulling them to the front.
· Place the headrest in the highest position and loosen the screw. Pull the guide rail out and slightly
downwards, and remove the shoulder pad retaining belt. Next remove the guide rail (fig. 18).
· In order to remove the shoulder pads remove the headrest cover and push the shoulder pads
through the harness slot. You can then remove the shoulder pads.
· Partially remove the seat cover and unhook the lap belt from the body shell (fig. 19).
· Unclip the base plate and turn it away to the side (fig. 20).
· Unhook the metal plate from the crotch strap and pull the strap out by the buckle by pulling away
from the seat (fig. 21).
· Turn the base plate back to its original position and push it back into place (fig. 22).
· Put the metal connector in the pocket on bottom of the base plate (fig. 23).
NOTICE: The belt-part with the metal connector has to remain on the child seat.
3.2 Securing the seat and child in using the three-point seatbelt
· The recline position must not be used for group II or above!
· Allow your child to sit in the seat and insert the lap belt of the three-point seatbelt into the front belt
guides. Fasten the seatbelt buckle so that it closes with an audible click (fig. 24).
· Insert the diagonal belt into the guide on the headrest (fig. 25).
· Adjust the headrest for your child's height. The belt is in an optimal position when it runs over the
middle of the collarbone and not too close to the child's neck (fig. 26).
EN
11
Werbung
Inhaltsverzeichnis
