Troubleshooting - Steinbach 00-40590 Bedienungsanleitung

EN
Safety Warnings
Your cartridge filter has been thoroughly tested after production and
left the factory in technically perfect condition. In order to maintain
this condition and to ensure safe functioning, the user should ob-
serve all the recommendations given in these instructions at all
times. If there are any signs that safe operation of the cartridge filter
may no longer be guaranteed, the system is to be disconnected from
the electricity supply immediately and secured against unintentional
switching on again.
This is the case:
 if the device shows visible damage.
 if the device appears to be no longer functioning correctly.
Set-Up Diagram (Picture 1)
Note: The cartridge filter can be adjusted in height. The extension
rod and clamp are fixed in place with a flat-head, star-drive screw
and a hexagon nut to avoid the device floating to the surface in the
pool.
Technical Data
Model Suspended/Wall-mounted cartridge filter for set-up pools
Nominal voltage
Filter volume
Flow rate
Pool volume
Output (W)
Max. Watertemp. °C
Max. depth below water (m)
Transformer
VAC 1700MA 20,4 VA
Safety Warnings (Picture 2)
 Do not use the pump if there is no water in the pool.
 Before the filter pump is started up, please check that all cables
and the plug are in perfect condition.
 Voltage and frequency must comply with those stated.
 The transformer must be kept at a distance of at least 3.5 metres
from the pool.
 The transformer, cable and plug must be kept dry.
 Before servicing the pump and cleaning the particle filter, make
sure that the transformer has been disconnected from the electrici-
ty supply.
 If the power cable is damaged, the pump must not be used.
 This device is not for intended for use by persons (including chil-
dren) with limited physical, sensory or mental abilities or those with
lack of experience and/or lack of knowledge, unless they have
been given the task by a person responsible for their safety or
have received instructions on how to use the device.
 Children should be supervised to ensure that they do not play with
the device.
 If the connecting cable on this device is damaged, it must be re-
placed by the manufacturer or his After-Sales Service or a similarly
qualified person in order to avoid hazards.
 Do not lift or move the pump by pulling on the power cable.
Using for the first time
Kartuschenfilteranlage | 2013_V1
12 VAC (50HZ)
2,8 l
1.700 l/h
8.000 l
20
35
0,5
SG12 20,4 W, 230 V 50 Hz, 12
Caution: never let the pump run dry; this leads to damage.
 Submerge the filter pump completely in the water and ensure that
the pump is filled with water.
 In order to avoid the pump sucking air, submerge the pump at
least 15 cm below water level.
 The water temperature must not be above 35°C.
 During winter avoid the pump becoming frozen.
 The pump switches on immediately after plugging the transformer
into the socket.
Winter
 Unplug the pump from the power source.
 Store the filter system in a location protected from frost and se-
verely cold temperatures. In a garage or insulated storage shed
is recommended.

Troubleshooting

Problem Cause
No electricity
Motor does not
run
Impeller is blocked
Windings burnt out
Pump is not fully sub-
merged in water
Impeller damaged
Motor runs but
little or no water
Rotor turns in the wrong
is drawn in
direction
Motor runs in- Impeller is blocked or is
termittently permanently overloaded
Steinbach VertriebsgmbH,
Aistingerstrasse 2, 4311 Schwertberg, Österreich
FR/IT/CZ/HU/HR/SK/SLO/RO/BG/TR: +43 (0) 7262 / 61431-0
e-mail: service@steinbach.at
www.steinbach.at
Possible remedy
Check electricity
source, switch and
wiring (have them
repaired or re-
placed by profes-
sionals)
Dismantle pump
and clean
Replace pump
Raise water level
or lower pump
Clean filter insert
Switch transformer
off and then back
on again
Clean cartridge
and protect trans-
former against
overheating.
Page 3 of 14