Braun A1 Gebrauchsanweisung Seite 8

English
@ntrols, displays,
Front panel
COnngCtiOnS
1 "Power" on/off switch
2 Stereo headphones jack (6.3 mm jack,
Note: With the push-button controls, the stereo as per IEC 130-8)
desired function is obtained by depres-
sing the corresponding button. The controls (3) to (13) can be found by
With all rotary controls, turning to the opening the front flap.
right increases their etfect. 3,4 Push-button for loudspeakers 1, 2 or
1 a n d 2
5 Push-button "tone defeat" (over-rides
the bass and treble controls)
6 Push-button "filter 30 Hz"
( s u b s o n i c f i l t e r )
7 Push-button "filter 7.5,, kHz (high cut)
8 P u s h - b u t t o n . . m o n o '
9 P u s h - b u t t o n " l i n e a r " ( s w i t c h e s t h e l o u d -
n e s s c o m p e n s a t i o n o u t )
10 Push-button "display sens> (increases the
s e n s i t i v i t y o f t h e L E D d i s p l a y ( 1 4 ) )
11 Rotary control ,.bass,
12 Rotary control "treble'
13 Rotary control "balance" with a centre
l o c a t i o n p o i n t
14 2 LED displays (for left and right chan-
n e l ) w i t h t h e f o l l o w i n g m a r k i n g s :
. , o n , , i s i l l u m i n a t e d i n g r e e n w h e n t h e
power is switched on
"16-0" level indicators (green) for both
c h a n n e l s i n d B
" c l i p o ( c l i p p i n g ) i l l u m i n a t e s r e d w h e n t h e
power amplifier is overloaded.
15 Rotary switch "record selector" selects
the source to be recorded.
16 Rotary switch "input selector" selects
t h e s o u r c e w h i c h w i l l b e h e a r d t h r o u g h
the loudspeakers.
17 Rotary control ..volume'
Back of amplifier
1 8 E a r t h i n g s c r e w " p h o n o + " ( f o r t h e t u r n -
table earth lead)
1 9 " p h o n o " s o c k e t s t o c o n n e c t t u r n t a b l e 1
2 0 " p h o n o " s o c k e t s t o c o n n e c t t u r n t a b l e 2
21 "tuner" sockets
22,,aux,, sockets to connect another signal
s o u r c e e . g . a m i c r o p h o n e a m p l i f i e r ( s e e
t e c h n i c a l d a t a r e g a r d i n g s i g n a l s t r e n g t h
a n d i m p e d a n c e )
23 "tape 1 in" sockets
(tape or cassette deck 1)
24 "Iape 1 out" sockets
(tape or cassette deck 1)
25 "tape 2 in" sockets
(tape or cassette deck 2)
26 "tape 2 out" sockets
(tape or cassette deck 2)
27,,pre-out" (p re-ampl ifier output)
2 8 " m a i n - i n " ( p o w e r a m p l i f i e r i n p u t )
Note: Sockets (27) and (28) are con-
nected according to channel by means
o f a j u m p e r .
29 Push-in connectors "speakers 1"
30 Push-in connectors "speakers 2"
31 AC power cable
32 Grooves for fixing back cover
33 Indentations for locating the feet of unit
placed on top
All cinch sockets at the back of the
amplifier are in accordance with IEC
S p e c . 1 3 0 - 8