Maintenance - Niko 350-20080 Gebrauchsanleitung

350-20080
• By pressing and holding the push button while the lighting is switched off, the lighting will be switched
on (irrespective of the daylight level). The lighting remains switched on for as long as activity is detected
and the preset switch-off delay + 2 hours has not yet elapsed. After that, the lighting will be switched off
and the detector will return to the selected settings.
The red indication LED on the detector flashes (0.25 s on and 5 s off) to indicate that you have pressed and held
the push button. The 'long push' function can be interrupted at any time by briefly pressing the push button, after
which the lighting will be switched on and the detector will return to the selected settings.
Example 2: double-height room
DIP switch 1 DIP switch 3
ON x
OFF x
How the absence detector works:
- The lighting must be switched on by briefly pressing the push button (daylight-independent).
- The 'eco off' and 'long push' functions are deactivated.
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area or the light level has been higher than the preset
lux value for five minutes.
Example 3: staircase
DIP switch 1 DIP switch 3
ON x x
OFF
How the presence detector works:
- The lighting is automatically switched on when the detector detects motion in the detection area and the
light level is less than the preset lux value.
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area or the light level has been higher than the preset
lux value for five minutes.
- The lighting can be switched on manually at any time via the push button, irrespective of the daylight level.

6. MAINTENANCE

Dirt may prevent the detector from functioning properly. Therefore, always keep the lens clean and dry. Use a
damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens clean. If
the lens or other parts of the detector are defective, please contact an authorised installer.
7. TECHNICAL DATA
dimensions
power supply voltage
power consumption
relay contact
maximum load
maximum switching capacity
maximum inrush current
light sensitivity
hysteresis on light sensitivity
switch-off delay
mounting height (fig. 3)
detection angle (fig. 3)
detection range (fig. 3)
wire input
cable inlet
12
protection degree
protection class
ambient temperature
quality mark
EN nv Niko sa
DIP switch 4
x
DIP switch 4
x
45.9 x 117.3 mm (HxW)
64.1 x 117.3 mm (HxW) (including non-visible part)
230 Vac ± 10%, 50 Hz
0.2 W
NO (max. 10 A), potential-free,
light- and motion-sensitive
incandescent lamps (2300 W)
230 V halogen lamps (2300 W)
all low-voltage halogen lamps (1200 VA)
fluorescent lamps (non-compensated) (1200 VA)
economy lamps (CFLi) (350 W)
LED lamps 230 V (350 W)
140 μF
165 A/20 ms or 800 A/200 μs
20 – 1000 lux
+ 10%
2 – 60 min
4 – 8 m
360°
circular, 16 – 32 m
3 x 2.5 mm²
on the side: 3 x Ø 14 mm
on the top: 2 x Ø 14 mm
IP54
class I devices
-5 – +50°C
CE marked in compliance with EN 60669-2-1
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
accessories
8. EC MARKING
This product complies with all of the relevant European guidelines and regulations. For radio equipment
Niko nv declares that the radio equipment in this manual conforms with the 2014/53/EU directive. If
applicable, the full text of the EU Declaration of Conformity can be found on www.niko.eu.
9. WARNINGS REGARDING INSTALLATION
The installation of products that will permanently be part of the electrical installation and which include dangerous
voltages, should be carried out by a qualified installer and in accordance with the applicable regulations.
This user manual must be presented to the user. It should be included in the electrical installation file and it should
be passed on to any new owners. Additional copies are available on the Niko website or via Niko customer services.
10. ENVIRONMENT
This product and/or the batteries provided cannot be deposited in non-recyclable waste. Take your
discarded product to a recognised collection point. Just like producers and importers, you too play an
important role in the promotion of sorting, recycling and reuse of discarded electrical and electronic
equipment. To finance the rubbish collection and waste treatment, the government levies recycling
charges in certain cases (included in the price of this product).
11. NIKO CUSTOMER SERVICES
Do you have a question or is the product faulty? Contact your wholesaler or Niko customer services (Belgium:
+32 3 778 90 80) or consult the 'Help and Advice' section on www.niko.eu.
12. DISCLAIMER
Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up-to-date
as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than
within the legal limits.
Please inform us of any deficiencies in the manuals by contacting Niko customer services at support@niko.eu.
IR remote control (350-20089)
presence or absence detectors 360° (slaves)
(350-20071, 350-20079, 350-20081)
PM350-20080R18051