Denon DJ Prime 4 Schnellstartanleitung Seite 5

14. Channel Fader: Use this fader to adjust the channel's volume level.
15. Crossfader Assign: Routes the audio playing on the corresponding channel to either side of the crossfader (L or
R), or bypasses the crossfader and sends the audio directly to the program mix (center, Thru).
16. Crossfader: Use this crossfader to mix between channels assigned to the left and right sides of the crossfader.
17. Master Level Meters: These LEDs display the audio signal level of the master mix (sent out of the Master
Outputs).
18. Phones Mix: Adjusts the software's audio output to the headphones, mixing between the cue output and the
master mix output.
19. Phones Level: Adjusts the volume of the headphones.
20. Split Cue: When this switch is in the On position, the headphone audio will be "split" such that all channels sent
to cue channel are summed to mono and sent to the left headphone channel and the master mix is summed to
mono and sent to the right channel. When the switch is in the Off position, the cue channel and master mix will
be "blended" together.
21. Sweep FX Buttons: Press one of these buttons to enable or disable an effect that you can control with the
Sweep FX knobs. Only one of these buttons can be enabled at a time.
• Filter: This effect applies a filter to the channel. Starting from the center (12:00) position, turn a Sweep FX
knob counter-clockwise to apply a low-pass filter, or turn it clockwise to apply a high-pass filter.
• Echo: This effect is a brief echo. Starting from the center (12:00) position, turn a Sweep FX knob counter-
clockwise to decrease the length of the delay and increase the feedback, or turn it clockwise to increase the
length of the delay as well as the feedback.
• Noise: This effect adds noise to the signal. Starting from the center (12:00) position, turn a Sweep FX knob
counter-clockwise to add pink noise, or turn it clockwise to add white noise.
• Wash Out: This creates a transition effect. Turn a Sweep FX knob to its most counter-clockwise (minimum)
position to apply a 1-beat echo that will also mute the channel's normal audio signal, or turn it to its most
clockwise (maximum) position to apply a 1/2-beat echo.
22. Platter: This capacitive, touch-sensitive platter controls the audio playhead when the wheel is touched and
moved. When the Vinyl button is on, move the platter to "scratch" the track as you would with a vinyl record.
When the Vinyl button is off (or if you are touching only the side of the platter), move the platter to temporarily
adjust the track's speed.
23. Platter Display: This display shows information relevant to the performance, including the current playhead
position, the current auto loop size, or current layer.
24. Deck: Selects which deck in the software is controlled by that hardware deck. The left deck can control Deck 1
or 3; the right deck can control Deck 2 or 4.
Press and hold Shift and then press the Deck 3 or Deck 4 buttons to switch between four-deck and two-deck
operation.
25. Track Skip: Press either of these buttons to skip to the previous or next track.
Press the Previous Track button in the middle of a track to return to the beginning of the track.
26. Beat Jump: Press either of these buttons to skip backward or forward through the track. Use the Auto Loop
knob to determine the beat jump size.
Press and hold Shift and then press one of these buttons to search backward or forward through the track.
27. Sync / Sync Off: Press this button to activate sync.
Press and hold Shift and press this button to deactivate Sync. You can also set Sync to deactivate without using
Shift by changing the Sync Button Action setting in the User Preferences menu.
28. Cue / Track Start: During playback, press this button to return the track to a temporary cue point. If you have
not set a temporary cue point, then press this button to return to the start of the track. (To set a temporary cue
point, make sure the track is paused, move the platter to place the audio playhead at the desired location, and
then press this button.)
During playback, press and hold Shift and press this button to set the cue point at the current playhead position.
If the deck is paused, press and hold this button to play the track from the temporary cue point. Release the
button to return the track to the temporary cue point and pause it. To continue playback without returning to the
temporary cue point, press and hold this button and then press and hold the Play button, and then release both
buttons.
5