Led Lenser M17R Gebrauchsanleitung Seite 6

˚ English
11. Charge indication
Approx. 2 cm before the end of the shaft of the M17R, there is a narrow ring, which, during the charging process, indicates the charge status of the
battery through lamps of different colours.
Red (glowing continuously) – charging ongoing.
Green (glowing continuously) – Charging completed, the M17R is ready for use with the full capacity of the battery. It generally takes 2 to 3 hours
for an empty M17R to get fully charged.
No light– The cause of this can be that the Floating Charge System
contact. Therefore, check whether (magnetic) objects or dirt are hindering a good contact between the charging contacts at the end of the M17R
and the magnetic charging socket. If required, remove them. If required, also correct the position or the angle of the M17R in the charging socket.
If, given an adequate electric power supply, the charge indicators still do not glow, immediately isolate the transformer or the optional car charger of
the M17R from the present power supply system and get in touch with your dealer.
12. 360° Power Indicator
The 360° Power Indicator consists of 10 blue-glowing elements, which are arranged in a circle around the two concentric charging contacts at the
end of the shaft of the M17R.
During use, the number of blue-glowing elements reduces further and just before the Power Module is empty, the last element glows in red.
Depending on when the charging contacts are pressed, the following can be determined from the number of elements glowing.
1.) Battery status indication
If the charging contacts are pressed while the M17R is off, the elements serve as a battery charging status indication. If, for example, all the 10
elements briefly glow blue, the M17R is fully charged.
2.) Operating time indication
If the charging contacts of the M17R are pressed while the M17R is being operated with a Light Function, the number of glowing elements provides
an indication of the remaining relative lighting duration of the current Light Function.
The M17R also shows this information for a brief moment when a light function has been selected by tapping or switching at the "Fast Action
Switch", i.e. even without the 360° Power Indicator having been actuated.
13. Changing the Power Module
Please charge the rechargeable battery in time. If the Power Module exhibits any atypical behaviour, please change it. For changing this
accumulator, please first switch off the pocket torch without fail, and unscrew the part behind the "Fast Action Switch". You have thus separated the
lamp head from the Power Module (shaft including "Safety Ytrion Cell" battery pack). For the disposal of the used Power Module, please read Point
14.
Screw on a new Power Module onto the lamp head till it cannot be turned any more. Thanks to the innovative new contact system and the fixed
connection between the lamp shaft and the "Safety Ytrion Cell" battery pack (Power Module), transposition of the polarity is not possible.
14. Rechargeable batteries / Accumulators
Only the correspondingly approved LED LENSER Power Module, consisting of the "Safety Ytrion Cell" battery pack and shaft, may be used in this
pocket torch. The Power Module was developed to ensure the highest level of safety and benefit.
If you have separated the used Power Module from the lamp head as described in Point 13, please unscrew the rear part of the shaft at the level
of the charging display. You will then see a PCB of the "Safety Ytrion Cell" battery pack on this side as well, upon looking into the tube. The PCB is
held in place on this side in the shaft by a narrow plastic ring with thread. For removing the "Safety Ytrion Cell" battery pack from the shaft, unscrew
this plastic ring from the shaft. For doing so, use the two grooves in the plastic ring that are displaced 180° from one another but make sure that
that you do not short circuit the contacts of the "Safety Ytrion Cell" battery pack. The "Safety Ytrion Cell" battery pack can now be easily removed
and disposed of in keeping with the national laws. The shaft can be disposed of in the domestic trash.
In contrast to the Power Module (shaft with "Safety Ytrion Cell"), a replacement of a "Safety Ytrion Cell" battery pack in a Power Module may not
be carried out. Neither is it permitted, after removal of the "Safety Ytrion Cell" battery pack, to charge it in any other manner or instead, to use
accumulators or batteries in the Power Module. The Power Module may only be opened once, for separate disposal of the Ytrion Cell battery pack
and the shaft; otherwise, the manufacturer's warranty will be rendered null and void.
In general, for the disposal of batteries as well as particularly for Lithium batteries, accumulators and accumulator packs, the applicable rule is that
they may only be disposed of in discharged state and in a technically correct manner. If they are not discharged, then before disposal, by sticking
non-conducting adhesive tape over the contacts, it has to be ensured that short-circuits are not possible.
Basically, the possibility of short-circuits of accumulators and batteries must be eliminated and they may neither be opened, nor enter the human
body in any way, nor may they be thrown into a fire.
15. Cleaning
For cleaning, please use a dry, lint-free clean cloth.
If salt water is spilled on the lamp, it must be immediately entirely removed with such a cloth.
If it is not possible to rotate the selection ring of the "Fast Action Switch" smoothly any more, it must be separated from the M17R, and the underside
and the lamp tubes cleaned of dirt. To do so, with the screws, separate the lamp head from the Power Module. Carefully remove the black O-ring of
rubber that is located above the lamp head thread. When the switch button is now pressed deep, the selection ring can be removed over the switch
button in the direction of the thread. Please ensure here that the small spring-loaded ball including its casing above the switch button is not lost.
Both surfaces can now be cleaned and the parts can be assembled again in the opposite sequence.
If the reflector lens has got loose in the lamp head or, e.g. dirt has got deposited on its inner side, you can apply the following remedial measures.
The foremost one centimetre of the M17R, with the 12 indicated holes along the periphery, can be unscrewed. There is a plastic ring that fixes
the reflector lens in it, and it can be tightened or removed for cleaning. You can clean the reflector lens if required, with a dry, lint-free clean cloth.
Thereafter, please assemble everything in the opposite sequence.
16. Scope of delivery
The M17R is supplied in a hard case with the following accessories:
1 x Floating Charge System Pro
- mains plug
- charger with extension cable (Input: 100 V to 240 V / 50 Hz to 60 Hz)
- magnetic charging socket (magnetic charger) with cable and blue position light as connection between the charger and the M17R
- charger bracket – for fastening the charger components, e.g. to a wall
1 x operating manual
1 x Smart Instruction Card as an addition to the operating manual
1 x Intelligent Clip for fastening the M17R e.g. to belts up to max. 60 mm width
Additional accessories for the M17R are being designed (e.g. anti-roll protection, colour filter, signalling cones, spare accumulators, Floating Charge
System , car chargers etc.).
Pro
You can get information on these additional accessories over and above the supplied kit on our Internet page.
17. Caution:
Do not swallow any small parts or batteries that are present. The products or parts thereof (including batteries) must be stored outside the reach of
children.
For reasons of safety and approval (CE), the product must not be modified and/or changed. The product is to be used exclusively as a pocket torch.
05
is not getting adequate electric power. But it can also be that there is a loose
Pro