Vestamatic VestaFunk R/M/J Montage- Und Bedienungsanleitung Seite 2

VestaFunk R/M/J
Installation and Operating Instructions
VestaFunk R/M/J
1. Safety precautions
· Please note that the Vestamatic VestaFunk R/M/J requires
an operating voltage of 230 VW, 50 Hz. Contact a profes-
sional electrician to install the control system.
· VestaFunk R/M/J is approved for indoor use only.
· The VestaFunk R/M/J was designed for correct use as de-
scribed in the operating instructions. Any changes or modi-
fications thereof are not permissible and will result in loss
of all warranty claims.
· Immediately after unpacking the VestaFunk R/M/J, check
for possible damage. If the device or cables are damaged,
do not operate under any circumstances. If you notice any
shipping damage, notify your supplier immediately.
· If safe operation of the VestaFunk R/M/J cannot be guaran-
teed, the control must be turned off immediately and pro-
tected against unintentional operation. Do the same if any
alteration work is being carried out on the windows or shut-
ters to which the VestaFunk R/M/J is connected.
· Certain structural materials, e.g. metal surfaces or thick or
heavily reinforced ceilings and walls, can reduce the trans-
mitter's range. Likewise, other devices sharing the same
radio frequency (868.3 MHz) can interfere with the radio
system or be affected by it. For safety reasons, if there is
any doubt concerning a radio signal's origin, the relevant
VestaFunk system function will not be performed.
· To achieve optimum reception quality, the above points must
be observed and the use of two or more radio receivers or
transmitters in the immediate vicinity should be avoided.
We recommend that you maintain a minimum distance of
50 cm between each device.
· Device batteries should be correctly removed and disposed
of before disposing of the VestaFunk R/M/J transmitter.
2. Functional description
R/M operating mode provides wireless control of shutters and
awnings.
J operating mode controls sunshading devices such as blinds.
You can independently control your sunshades according to
your requirements using a VestaFunk transmitter (see section
"Overview of VestaFunk system components").
Programming and cancelling the VestaFunk R/M/J and chang-
ing operating mode can be performed using either the pro-
gramming stylus (supplied) or the round end of the 12 or 4 M/L
WISO hand-held VestaFunk transmitter.
3. Installing the control
Only an authorised electrician is permitted to install the
Vestamatic VestaFunk R/M/J.
1. Switch off the power supply.
2. Connect the VestaFunk R/M/J according to the wiring dia-
gram.
Warning: Currently valid VDE standards must be ob-
served when connecting the device, in par-
ticular DIN VDE 0100/0700 as well as the cur-
rently valid regulations of your local power
company and accident prevention regula-
tions.
Parallel control of more than one conventional drive
motor can only be implemented by means of isolating
relays and group control devices.
For the control of two drives, we recommend our isolating
relays:
Isolating relay TR N2S, article-no. 01054220
Isolating relay TR N2A, article-no. 01054120
3. Switch the power supply on. The VestaFunk R/M/J performs
a retract command. While this command is being performed,
check that the motor is moving in the right direction. If this
is not the case, swap over the brown and black wires in the
VestaFunk R/M/J motor connecting cable.
4. Then programme a VestaFunk transmitter by referring to
the section "Programming and cancelling a VestaFunk hand-
held transmitter".
4. Wiring diagram
Contents
1. Safety precautions
2. Functional description
3. Installing the control
4. Wiring diagram
5. Dimensions diagram
6. Programming and cancelling
a VestaFunk hand-held transmitter
7. Cancelling all VestaFunk radio transmitters
8. Operation
9. Changing operating mode
9.1 Changing R/M operating mode
to J operating mode
9.2 Changing J operating mode
to R/M operating mode
10. Additional notes
11. Technical data
12. Warranty terms
13. Overview of VestaFunk system components
5. Dimensions diagram
6. Programming and cancelling
a VestaFunk hand-held transmitter
Programming
– Briefly point the round end of the VestaFunk hand-held
transmitter (the example shows a 12 M/L VestaFunk hand-
held transmitter) (see Figure 1a) or the programming stylus
(see Figure 1b) at the front end (the end with the antenna)
of the VestaFunk R/M/J.
– The LED on the front of the VestaFunk R/M/J starts to flash
and device performs a short extend and retract command.
O
– Then press the button corresponding to the channel
on the hand-held transmitter that you wish to programme.
– The LED on the front of the VestaFunk R/M/J goes out and
device performs a short extend and retract command.
Programming of this channel is now effective.
Cancelling
– Briefly point the round end of the VestaFunk hand-held
transmitter (the example shows a 12 M/L VestaFunk hand-
held transmitter) (see Figure 1a) or the programming stylus
(see Figure 1b) at the front end of the VestaFunk R/M/J.
– The LED on the front of the VestaFunk R/M/J starts to flash
and device performs a short extend and retract command.
o
– Then press the button corresponding to the channel
on the hand-held transmitter that you wish to cancel.
– The LED on the front of the VestaFunk R/M/J goes out and
device performs a short extend and retract command.
Cancellation of this channel is now effective
7. Cancelling all VestaFunk
radio transmitters
To cancel all settings of the VestaFunk transmitter, proceed
as follows:
– Point the round end of the VestaFunk hand-held transmit-
ter (the example shows a 12 M/L VestaFunk hand-held
transmitter) (see Figure 1a) or the programming stylus
(see Figure 1b) at the front end of the VestaFunk R/M/J for
10 seconds without interruption.
– The LED on the front of the VestaFunk R/M/J will flash
3 times and device performs a short extend and retract com-
mand.
– All VestaFunk transmitter settings are cancelled.
8. Operation
R/M operating mode
O o
In this operating mode, press the or button on a pro-
grammed hand-held transmitter to operate your sunshade.
The sunshade will immediately retract or extend.
To interrupt the sunshade's movement, press the opposite
button, i.e.:
O
· if the sunshade is extending, press the button,
o
· if the sunshade is retracting, press the button,
O o
Press the or button again to resume retraction/
extension.
J operating mode
O o
In this operating mode, press and hold the or
on a programmed hand-held transmitter for 2 seconds to fully
retract or extend your sunshade.
To interrupt the sunshade's movement, press the opposite
button, i.e.:
O
· if the sunshade is extending, press the button,
o
· if the sunshade is retracting, press the button,
O o
Press the or button again to resume retraction/
extension.
If you press and hold the buttons for less than 2 seconds, the
sunshade will only retract or extend for the time that you hold
the button down. This enables you to accurately position the
blind's slats and to set them at the correct angle.
Picture 1a)
Picture 1b)
9. Changing operating mode
The VestaFunk R/M/J is set by default to R/M operating mode.
The operating mode can only be changed if all VestaFunk
transmitters are cancelled.
If you wish to change operating mode, proceed as follows:
9.1 Changing R/M operating mode
to J operating mode
– Ensure that the connected sunshade is fully retracted. If this
is not the case, fully retract the sunshade.
– Point the round end of the VestaFunk hand-held transmitter
(the example shows a 12 M/L VestaFunk hand-held trans-
mitter) (see Figure 1a) or the programming stylus (see
Figure 1b) at the front end of the VestaFunk R/M/J for
10 seconds without interruption.
– The LED on the front of the VestaFunk R/M/J will flash
3 times and device performs a short extend and retract com-
mand.
– While the LED is flashing, or within the next 3 seconds, point
the hand-held transmitter (see Figure 1a) or the program-
ming stylus (see Figure 1b) at the front of the VestaFunk
R/M/J for another 10 seconds without interruption.
– The LED on the front of the VestaFunk R/M/J will briefly flash
twice every 1.5 seconds and the sunshade will extend
three times for 1.5 seconds with short pauses between
each extension.
– The VestaFunk R/M/J will then perform a 6-second retract
command.
– The VestaFunk R/M/J is now in J operating mode.
9.2 Changing J operating mode
to R/M operating mode
– Ensure that the connected sunshade is fully retracted. If this
is not the case, fully retract the sunshade.
– Point the round end of the VestaFunk hand-held transmitter
(the example shows a 12 M/L VestaFunk hand-held trans-
mitter) (see Figure 1a) or the programming stylus (see
Figure 1b) at the front end of the VestaFunk R/M/J for
10 seconds without interruption.
– The LED on the front of the VestaFunk R/M/J will flash
3 times and device performs a short extend and retract com-
mand.
– While the LED is flashing, or within the next 3 seconds, point
the hand-held transmitter (see Figure 1a) or the program-
ming stylus (see Figure 1b) at the front of the VestaFunk
R/M/J for another 10 seconds without interruption.
– The LED on the front of the VestaFunk R/M/J now flashes
every 1.5 seconds and the sunshade will extend for 4.5
seconds.
– The VestaFunk R/M/J will then perform a 6-second retract
command.
– The VestaFunk R/M/J is now in R/M operating mode.
10. Additional notes
· If the LED on the VestaFunk transmitter stops lighting up
when the button is pressed, or the transmitter range is dra-
matically reduced, you will need to replace the batteries.
Refer to the relevant transmitter operating instructions for
information on replacing batteries and battery types.
· Also refer to the relevant operating instructions for infor-
mation on programming and cancelling the VestaFunk
R/M/J and changing operating mode using the VestaFunk
transmitter not described in the example.
Personal notes
button
11. Technical data
Power supply: 230 VW, 50 Hz
Impulse voltage
withstand level: 2.5 kV
Rated power: approx. 2 W
Output:
Maximum load: 250 VW, 50 Hz,
4A, cos f > 0.8 ind.
Align switching time: 180 seconds
Software class: A
Operating temperature: -15 °C (+5 °F) to +45 °C (113 °F)
IP class: IP 65
Degree of contamination: 2
Receive frequency: 868.3 MHz
p The CE mark is a free market mark, which exclusive-
ly refers to the authority but does not guarantee any
properties. For the comprehensive declaration of con-
formity for this product, please refer to our Internet
homepage: http://www.vestamatic.de
All technical data is subject to change.
12. Warranty terms
For new devices, the Vestamatic GmbH issues a warranty period
of 24 months, starting from the date of purchase, provided the
device was mounted in accordance with the installation in-
structions. The warranty extent applies to all design, material
and manufacturing defects.
Not included in the warranty extent are faults and defects due to:
– faulty mounting or installation,
– failure to observe of the installation and operating in-
structions,
– inappropriate operation and strain,
– detrimental effects such as impacts or weather,
– non-authorized repairs or modifications,
– use of inappropriate accessories.
Product deficiencies occurring within the warranty period will be
remedied free-of-charge by Vestamatic, either by means of
repair or by exchange of the device. A replacement delivery
due to warranty claims does not prolong the original warranty
period. The buyer bears all costs for mounting and installation.
13. Overview of VestaFunk system
components
This VestaFunk receiver can be controlled with the following
VestaFunk transmitters:
VestaFunk Hand-held trans-
mitter 12 M/L article-no. 01560000
VestaFunk Hand-held trans-
mitter 4 M/L WISO article-no. 01560010
VestaFunk Hand-held trans-
mitter1 M/L article-no. 01560100
VestaFunk Wall radio transmitter 1 M/L article-no. 01560200
VestaFunk Wall radio transmitter 2 M/L article-no. 01560210
Timer Control Funk article-no. 01813810
The disposal of electrical equipment and batteries
é
in household waste is strictly forbidden.
The symbol (dustbin crossed out, in line with WEEE Appendix IV)
indicates separate collection of electrical and electronic products
in EU countries. Do not dispose of the device in your household
waste. Ask your town or local council about the return and col-
lection systems available in your area to dispose of this product.
Artikel-Nr.: 83202915 N2