Herunterladen Inhalt Inhalt Diese Seite drucken

Technical Data - EINHELL TC-PT 2500 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für TC-PT 2500:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Anleitung_TC_PT_2500_SPK7__ 29.03.16 14:27 Seite 10
GB

5. Technical data

Overall height:
Overall length:
Fork length:
Fork height min.:
Fork height max.:
Fork width single:
Fork width total:
Lift max.:
Load:
Weight approx.:
Steering wheels Ø:
Load-bearing rollers Ø:
6. Assembly
Note: The hydraulic system is secured with a bolt (M).
Do not remove it until prompted in the following
assembly description and keep it in a safe place for
future maintenance work.
1. (Fig. 1) Press down the control lever (2) as far as
it will go into the lowering position (see 6.
Functions).
2. (Fig. 2) Pass the control chain (F) through and out
of the recess at the bottom end of the drawbar.
3. (Fig. 3) Insert the bolt (B) through the hole in the
drawbar mount (C) and the hole in the drawbar.
Make sure that the clamping sleeve passage (E)
coincides with the clamping sleeve hole in the
bolt (B).
4. (Fig. 2) Pass the control chain (F) through the
hole in the bolt (B) so that the hydraulics system
works.
5. (Fig. 3) Hook the setting screw (H) with the pre-
mounted hex nut (K) into the hydraulics lever (L).
6. (Fig. 3) Press the drawbar (3) down a little so that
the hydraulics lock bolt (M) is slackened and can
be removed.
7. (Fig. 4) Check whether the clamping sleeve
mount of the bolt (B) coincides with the clamping
sleeve passage (E) in the drawbar mount. Use a
hammer and the hydraulics lock bolt (M) to hit the
sleeves (A) into the bolt (B) on the left and right.
Note: The equipment can be optionally equipped with
a foot-activated parking brake. If required, please
contact your customer service team.
10
Operating the foot-activated parking brake:
Push the brake to the right as far as the stop – the
wheels will be blocked.
1210 mm
Push the brake to the left – the wheels will be
1500 mm
released again.
1150 mm
80 mm
7. Functions
190 mm
153 mm
Important! Note the safety information (section 1.)
540 mm
and Figure 6.
110 mm
On the drawbar is a sticker showing the positions of
the handle switch (Fig. 5).
2500 kg
62 kg
1 = Lower (lowering position)
180 mm
2 = Travel (traveling position)
80 mm
3 = Lift (lifting position)
The pallet lifting truck is allowed to be parked only
when the lifting forks are lowered.
The following functions are possible and were already
set in the factory.
7.1 Lifting the load (Fig. 1)
Press down the control lever (2) (lifting position). Then
pump the drawbar (3) up and down several times. The
load will be lifted.
7.2 Pulling the load (Fig. 1)
Pull up the control lever (2) into the middle position
(traveling position). In this position the hydraulics
cannot be used for lifting or lowering.
7.3 Lowering the load (Fig. 1)
With the pallet lifting truck at a standstill, pull up the
control lever (2) to the very top (lowering position).
The load will be lowered. When you now release the
control lever (2), it will automatically return to the
middle position (traveling position).
8. Setting the hydraulics control
system
The functions described in section 7. will not work
correctly if the hydraulics control settings are altered.
In this case you must re-set the hydraulics control
system.
8.1 The lifting forks rise when the control lever is
in the traveling position
(Fig. 3) Turn the hex nut (K) on the setting screw (H)
clockwise to the point where the lifting forks no longer
rise and the traveling position works correctly.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis