Maintenance Intervals Table; Cleaning - Ringler RI 020 W1E-N Bedienungsanleitung

Pos : 12.17 /9 Wartung/Ins tandsetzung/Warntext El ektr of achkr aft @ 0\mod_1264055838943_131.doc x @ 1680 @ @ 1
•
These works may only be carried out by an electrician.
Pos : 12.18 /1 Grundlegende Sic her hei tshi nweise/Sic her hei tsinfor mationen Wec hs elstrom- Ger äte/vor Beginn j eder Arbeit.... frei z usc halten @ 0\mod_1269594559993_131.doc x @ 3730 @ @ 1
•
Before starting any work on the industrial vacuum cleaner, but particularly before opening covers of
live or moving parts, the industrial vacuum cleaner or system must be correctly disconnected from
the mains and the drive unit must have stopped
Pos : 12.19 /1 Grundlegende Sic her hei tshi nweise/Sic her hei tsinfor mationen Wec hs elstrom- Ger äte/Die üblic hen Sicherheitsr egel n lauten hi erbei z .B. nac h VDE 0105 @ 0\mod_1269594914059_131.doc x @ 3748 @ @ 1
•
The usual safety regulations are, for example, in accordance with VDE 0105:
– Disconnect from mains
– Provide a safeguard to prevent unintentional restarting
– Check that the equipment is not live
– Cover or shield adjacent live parts.
Pos : 12.20 /9 Wartung/Ins tandsetzung/T abelle Wartungsinter vall e, Ü berschrift @ 0\mod_1263810791405_131.doc x @ 1564 @ 2 @ 1
9.2

Maintenance intervals table

Pos : 12.21 /9 Wartung/Ins tandsetzung/RI/Tabelle Wartungsi nter vall Spänes auger Wechs elstr om @ 0 \mod_1269592589773_131.doc x @ 3717 @ @ 1
Interval
Daily
Weekly
Monthly
Annually
Pos : 12.22 /1 Grundlegende Sic her hei tshi nweise/Signal wort-F eld "Hinweis" @ 0\mod_1261404960439_131.doc x @ 905 @ @ 1
Pos : 12.23 /9 Wartung/Ins tandsetzung/R einigung Gerät @ 2 \mod_1340195497910_131.doc x @ 17554 @ 2 @ 1
9.3

Cleaning

Dust on the appliance must be avoided and must be removed by regularly cleaning.
Before cleaning the device, be sure to switch off the motor protection switch and unplug the device from the
power supply. Cleaning can take place with a damp cloth or a suitable industrial vacuum cleaner. Do not use
solvents such as thinner, alcohol or benzene. Never immerse the device in water.
Pos : 12.24 /0 Allgemeines/Sei tenumbruch @ 0\mod_1265272007940_0.doc x @ 2191 @ @ 1
22/46
Inspection
 Baffle plate correctly inserted?
 Suction tube leaking? (see List of wear
parts)
 Collecting tank full?
 Bag-type filter soiled? (see List of wear
parts)
 Seal between drive unit and collecting
tank (see List of wear parts)
 Collecting tank
 Level control and discharge tube
 Inspect carbon brushes (see List of
wear parts)
 Drive unit
 Insert correctly
 Replace tube
 Empty collecting tank
 Clean filter
 Clean or replace seal
 Clean
 Clean
 Replace if necessary
 BGV A3 inspection
NOTICE
Maintenance/Repair
Measure