Honeywell HFD323E Benutzerhandbuch Seite 4

CONTROLS
AUTO-OFF TIMER BUTTON
Push this button if you would like your air cleaner to run
and then automatically shut-off after a certain amount of
time (choose from between 2, 4, 6, 8, 10 and 12 hours).
This is convenient if you would like your air cleaner to run
during the night but then shut-off automatically in the
morning (choose the 8 or 10 hour setting).
PURIFICATION LEVEL BUTTON
Your air cleaner will start off on the General Cleaning
setting each time you turn your air cleaner on.
Level 5 – Max
Best for power cleaning the air when unpleasant odours
are noticeable, your room is particularly dusty or you
can sense that airborne particles are present. This
setting cleans the air the fastest of all the settings and
circulates the air frequently in a room.
Level 4 – Allergen
This setting makes the air cleaner perform at the proper
level for reducing many types of airborne allergens.
It ensures the allergen capturing efficiency and rate
is best for the particle sizes being captured. Best for
fighting airborne allergens during high allergen season,
particularly in the spring and fall to help reduce airborne
pollen. Also great for year-round reduction of pet
dander allergens.
Level 3 – General
Best for General Cleaning. Use this setting to help
reduce airborne dust and smoke particles, like those
from cooking or tobacco smoke.
Level 2 – Germ
This setting slows down air movement so airborne
microscopic germs are most effectively captured in
the filter. Germs, like certain bacteria and viruses,
can be much smaller than other airborne particles or
organisms. Giving the germs more time to dwell in the
filter increases the filtration efficiency. This setting
can be used during cold and flu season to help reduce
certain germs from the air that passes through the
filter.
Level 1 – Sleep
Best for ultra quiet operation, perfect for nighttime use
when sleeping.
FILTER STATUS AND CHECK FILTERS BUTTON
Allows you to monitor how dirty your filter is getting.
When it is time to check and clean the filter, an indicator
will illuminate notifying you that it is time to check the
filters. When this light comes on, you will need to clean
your primary ifD® Filter and clean or replace your pre-filter.
(See Filter Cleaning instructions). After you have cleaned
or replaced the filters, press the Filter Reset Button until
the light goes off.
ACCENT LIGHT INDICATOR
Your air cleaner features a soft accent light at the bottom
of the unit that provides a nice glow around the base. You
can choose to operate your unit with or without this accent
light turned on. If you want to use the light feature, you
can choose from between a low or high light level.
OSCILLATE BUTTON
Press this button if you want your air cleaner to gently
rotate from side to side.
This will help increase circulation in the room. The
oscillation feature is actived by pressing the Oscillation
button .
Press the oscillation button or 'Tap' the oscillation symbol
once to turn the feature on, and then again to turn it off.
TIMER
The timer option on the left of the control panel allows
you to select how long the unit will run before it turns off
automatically.
• 'Tap' the Timer symbol to shift through the options.
When pressed the time will move to the next highest
setting until it is on '12' (which means it will stay on
for 12 hours and then shut-off). If you press the Timer
button while it is on '12' the timer option will turn off
and the unit will run continuously. If you 'tap' it again, it
will start back at '2'.
• Cycle through the hour options until the LED light
is illuminated behind the number of hours you want
the unit to operate for. If the Auto-off Timer is not
illuminated, the air purifier will run continuously.
ELECTRONIC FILTER CHANGE REMINDER
This model air cleaner has an electronic filter check to
remind you when to check the washable ifD® Filter based
on the air purifier's hours of use.
• When the ifD® Filter need to be cleaned, the LED light
'bar' will remain full and the light will be illuminated
until it is RESET. You may unplug the air cleaner
without interrupting the filter check.
• You should periodically check the filter. Depending on
operating conditions, the filters should be cleaned at
least once every three months.
6
TO RESET EITHER ELECTRONIC FILTER
CHECK
• When the status indicator light remains on, it is time
to check/clean the ifD® Filter and reset the status
indicator, if needed.
• After the filters have been cleaned and placed back in
the unit (dry), you will want to reset the indicator. To do
this, 'touch' the 'OK' button for 3 or more seconds until
the status indicator is not illuminated.
FILTER REMOVAL
(See page 3)
CAUTION: Turn off the unit and wait 60 seconds before
removing the grille to clean filters.
The ifD® Filter is supplied within the air cleaner.
• Turn-off the air cleaner. Wait 60 seconds and unplug
the unit before removing the grille. While pressing down
on the notch along the rear grille, pull the grille down
and towards you and remove it (see Fig. 1). Gently push
along the edge of the filter frame and pull forward.
• Place back into the air cleaner housing and snap filter
grille back into place.
NOTE: If the odour reducing pre-filter is used in lieu
K
of the permanent washable pre-filter, it will need to be
replaced approximately every 3 months.
CLEANING THE IFD® FILTER
The ifD® filters should be cleaned approximately once
every 3 months.
To clean the ifD® Filter
After removing the ifD® Filter from the air purifier, follow
the steps below to wash the ifD® Filter.
Rinsing:
• Rinse the filter with clean tap water.
• If the filter still appears dirty, proceed to "Washing,"
otherwise proceed to "Drying."
Washing:
• Turn the power off and unplug the air purifier.
• Remove the ifD® Filter from the unit.
• Fill a sink with lukewarm water and add a few drops of
mild dish soap.
• Gently swish the filter in the soap solution to clean.
• Soak the filter for 2-3 minutes. Do not leave for an
extended period of time.
• Rinse the filter with clean tap water (Fig. 11).
Drying:
• Shake the filter to remove any excess water.
• Place the filter with the honeycomb side down on a
plush towel.
• Note that the filter may still be discolored even
after washing. This is acceptable and will not affect
performance.
• Allow the ifD® Filter to dry for a few hours or overnight.
• When the ifD® Filter is completely dry, place back into
the air purifier.
CAUTION:
• Never place a wet ifD® Filter in your air purifier.
• The ifD® Filter is NOT dishwasher safe. Do not place the
ifD® Filter in a dishwasher or subject it to other extreme
hot water conditions.
• Do not use any solvents, strong cleaning agents or
flammable liquids to clean the ifD® Filter.
MAINTAINING YOUR WASHABLE
PRE-FILTER
The pre-filter helps pick up large airborne particles that
enter the rear grille. This pre-filter can be periodically
removed and shaken to clean it. Alternatively, it can be
rinsed by hand under warm water. Let the pre-filter air dry
completely before inserting back into the grille.
OPTIONAL: Changing the Odour Reducing Pre-Filter
If you have chosen to use the optional odour reducing
pre-filter, it will lose its effectiveness for odour
K
adsorption over time and will need to be replaced.
If using the odour reducing pre-filter, it is
K
recommended that you store the original washable pre-
filter in the event that you decide to use it in the future.
To insert it into the unit, simply place securely into the rear
grille in lieu of standard pre-filter.
NOTE: The odour reducing pre-filter is not washable.
K
INSTALLATION INSTRUCTIONS FOR THE
ODOUR REDUCING PRE-FILTER
K
• Air purifier should be turned OFF, and unplugged prior
to replacing/inserting pre-filters.
• Remove the rear grille by pushing down on the release
tab at the top of the grille (see Fig. 5).
• If using the odour reducing pre-filter instead of the
K
washable permanent pre-filter you must first remove
the washable pre-filter (see Fig. 7).
7
(See page 3)