Maintenance; Specifications - Monacor M-32CD Bedienungsanleitung

1) Set the CD player to the stop mode; press the
button STOP (2), if required.
2) Activate the programming mode with the button
PROG (15). Press all other buttons within 15
seconds otherwise you will exit the program-
ming mode. In this case, press the button
PROG once again. The display will show:
— for a CD without MP3 files
PROGRAM
CD P – 01 00
— for a CD with MP3 files
PROGRAM
P – 01 000 0000
3) For CDs without MP3 files, skip this step and
directly proceed with step 4.
For MP3 files, first select the number of the
folder containing the first title desired for the title
sequence. This is also necessary when all the
files are in the ROOT directory without folder. In
this case, enter 1 as the folder number.
Select the folder number with the buttons
DOWN / REV and UP/ CUE [REV – SKIP – CUE*]
(3) or with the numerical keys (12). To memo-
rize, press the button PROG. The four zeroes
will flash as a prompt to enter the title number.
4) Select the number of the first title of the title
sequence with the buttons DOWN / REV and UP/
CUE (3) or enter it with the numerical keys (12).
For MP3 files in folders, please note that these
files are not arranged consecutively but that the
first file in each folder is always number 1.
5) To memorize press the button PROG. The dis-
play will show the next memory location number,
e. g. "P – 02".
6) Repeat steps (3), 4 and 5 for all further titles
desired until the entire title sequence has been
programmed.
7) To start the title sequence, press the button
PLAY/ PAUSE (4). The upper line of the display
will show "MEM" (memory) and the title
sequence will be replayed.
8) Press the buttons DOWN / REV and UP/ CUE to
select any title of the title sequence or keep the
corresponding button pressed to activate the fast
forward / reverse function within a title.
*Lettering on the remote control
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
9) The replay will stop after the title sequence has
Note: A programmed title sequence will be deleted when
you change the sound carrier, when you press the button
USB (10) or CD (11), when you press the button STOP in
the programming mode and when you switch off the
player.

6 Maintenance

Protect the player from dust, vibrations, humidity
and heat (admissible ambient temperature range
0 – 40 °C). For cleaning only use a dry, soft cloth;
never use water or chemicals.
Note concerning sound interruptions and read-
ing errors
Cigarette smoke and dust will easily penetrate
through all openings of the unit and will also settle
on the optics of the laser sampling systems. If this
deposit should cause reading errors and sound
interruptions, the unit must be cleaned by skilled
personnel. Please note that there will be a charge
on cleaning, even during the warranty period!

7 Specifications

Frequency range: . . . . . . 20 – 20 000 Hz
THD: . . . . . . . . . . . . . . . . < 0.1 %
Channel separation: . . . . > 60 dB
S/N ratio: . . . . . . . . . . . . . > 70 dB
Audio output: . . . . . . . . . . 1.2 V
Power supply: . . . . . . . . . 12 V , 800 mA
Ambient temperature: . . . 0 – 40 °C
Dimensions (W × H × D): . 174 × 52 × 160 mm
Mounting cutout
(W × H × D): . . . . . . . . . . . 155 × 50 × 150 mm
Weight: . . . . . . . . . . . . . . 1.3 kg
Subject to technical modification.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
been replayed or when you press the button
STOP. To restart the title sequence, first press
the button PROG, then the button PLAY/ PAUSE.
GB
13