Werbung
CMM611_022384 05.03.2002 11:42 Uhr Seite 4
English
Montage
Application
Video cameras mounted in the Vario
door loudspeaker or positioned
externally in the background, permit
unobtrusive observation of the
house entrance. A visitor is shown
on one or more monitors. The
assigned system telephone is used
for placing calls, communication and
door release. Any Siedle in-house
communication system can be fitted
with a door video unit, permitting
application in houses and apartment
blocks, companies, doctors'
surgeries and offices, etc..
The swivel-mounted CCD mono-
chrome or colour video camera is
intended for installation in the Siedle
Vario door loudspeaker. Compatible
with all Siedle-Vario housings GU...,
GA... ,door loudspeaker, communi-
cation columns surface mount or
feestanding with or without system
611 letter boxes.
These cameras are suitable for con-
tinuous operation.
Remember to plan for an instal-
lation height of 1.60 m!
Remark!
Cameras may not be aligned into
direct sunlight. In case of colour
cameras, this can lead to irreparable
damage. This type of damage is
not covered by the product
warranty.
Instead of mounting a built-in
camera, it is also possible to install
an external, weatherproof camera
KA/WG..., with a suitable zoom lens
and wall mounting arm. In this case,
supplementary out-side lighting
must be provided. Where this model
is used, the video camera mounted
in the Vario door loudspeaker is no
longer required.
CMM/CMC 611-... video cameras
can be swivelled horizontally by
± 20° using 4 control buttons in the
monitor MOM/MOC 611/711-... .
When using the monitor
MO 612-02, 4 external buttons must
be provided to control the camera
swivel motion.
4
Installation
Location of the video camera
Selection of the correct camera and
choice of location are decisive
factors in ensuring good image
quality.
The camera must not be directed
towards:
1 Direct back light, direct sunlight, a
bright pictorial background, highly
reflective walls or lamps, light
sources etc.
2 General pick-up range of camera
CMM/CMC 611-...
The mounting height is always
1.60 m.
The lighting integrated in the
camera module is generally sufficient
to obtain a perfect picture at night
3 For the external camera KA/WG,
the most suitable lens must be
selected depending on distance and
required image width.
Diagram to ascertain the focal
distance for:
a 1/3" and 1/4" image pick-up,
CMM/CMC 611-...
b 1/4" image pick-up,
CEC 611-... or KA/WG 950-0/...C
c 1/3" image pick-up,
CEM 611-... or KA/WG 950-0/...
Object width/ distance in m
4 To install the camera module, see
"Siedle-Vario Mounting instruction".
5 Connect the camera in accordance
with the relevant external wiring
diagram AS-TV-...
6 Connect the external control
buttons
7 Position the video cameras
opposite each other
Remark
For circuit diagrams and technical
details relating to power supply,
conductor material, wiring, range,
etc. please refer to the enclosed
manual "Video Systems Planning
and Installation"
Specifications CMM 611-0
Swivel-mounted single-module
monochrome CCD camera without
infrared filter and built-in lighting.
For Siedle Vario 611 integration.
• Image pick-up CCD sensor 1/3"
• Lens 3,6 mm, F 2 with electronic
shutter 1/50 - 1/ 100 000 sec. and
without IR filter
• 90° pick-up angle
• Horizontal and vertical swivel
range ± 20°
• Resolution: Horizontal 330, vertical
330 lines
• CCIR, 625 lines/50 Hz
• Light sensitivity 0.8 Lux
• Automatic gain control
• Video output 1 Vpp at 75 Ω
• Lighting integrated into camera
module, 12 V AC / 10 W
• Luminosity factor > 25 Lux at a
distance of 0.5 m
• Heater 12 V AC/ 150 mA
• Temperature range -10°C
to +40°C
• Power supply 20 - 30 VDC
• Power consumption max. 110 mA
Specifications CMM 611-1
as per CMM 611-0 beside
• Lens 3,6 mm, F2 with electronic
shuter 1/60 - 1/100 000 sec. and
without IR filter
• EIA, 525 lines/ 60 Hz
Werbung
