General Information - Novoferm Novomatic 553 S III Bedienungsanleitung

Garage
door
operator
Novomatic
553 S III
Contents

• General Information

- Safety
- Explanation of the symbols
- Working safety
- Dangers that may emanate from the product
- Spare parts
- Changes to the product
- Dismantling
- Disposal
- Data plate
- Packaging
- Technical data
• Installing Instructions
• Operating Instructions
• Maintenance and Inspection
• Trouble-shooting Guide
• Diagnostic Display
• Warranty terms
Inspection Log Book
•
- Inspection Log Book for the Door System
- Checklist for the Door System
- Proof of Inspection and Maintenance of the
Door System
- Declaration of Conformity and Incorporation
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
• General Information
Safety
Before commencing any work on the product,
carefully read through the operating instructions
from start to finish, in particular the section entitled
"Safety" and the related safety advice. It is important
for you to have understood what you have read. This
product could prove hazardous if not used properly
as directed or in accordance with the regulations.
Any damage occurring as a result of non-compliance
with these instructions shall render the manufactu-
rer's liability null and void.
• Explanation of the symbols
WARNING: imminent danger
This symbol indicates that instructions are
being given which, if not observed, could
lead to malfunctions and/or failure of the
operator.
WARNING! Danger by electric current
The works may only be executed by an
electrician.
This symbol indicates that instructions are
!
being given which, if not observed, could
lead to serious injury.
0
Reference to text and figure
Working safety
•
By complying with the safety advice and information
provided in these Operating Instructions, injury to
persons and damage to property whilst working on
and with the product can be avoided.
Failure to observe the safety advice and information
provided in these Operating Instructions as well as
the accident prevention and general safety
requirements relevant to the field of application shall
exempt the manufacturer or ist authorized
representatives from all liability and shall render any
damage claims null and void.
Hazards that may emanate from the product
•
The product has been subjected to a risk assess-
ment. The design and execution of the product
based on this corresponds to state-of-the-art
technology.
When used properly as intended, the product is safe
and reliable to operate.
Nevertheless, a residual risk will always remain!
The product runs on a high electrical voltage. Before
commencing any work on electrical systems, please
observe the following:
1. Disconnect from the power supply
2. Safeguard to prevent a power restart
3. Check that the electricity supply is cut off.
• Spare parts
Only use genuine spare parts of the manufacturer.
Wrong or faulty spare parts can cause
damage, malfunctions or even a total failure
of the product.
• Changes and modifications to the product
In order to prevent hazards and ensure optimum
performance, no changes, modifications or
conversions may be made to the product that have
not been expressly approved by the manufacturer.
• Dismantling
Dismantling takes place in reverse sequence to the
Installation Instructions 13 - 1.
• Disposal
Observe the corresponding country-specific
regulations.
PS
PC
PA6
• Data plate
The date plate is located under the control panel
cover. Observe the specified power rating.
• Packaging
Always dispose of the packaging in an environ-
mentlly-friendly manner and in accordance with the
local regulations on disposal.
Technical Data
•
Operator type: Novomatic 553 S III
Control: FUTURE III S
Power rating normal: 210N
Power rating max: 700
Connection values: 230V / 50Hz
Power input:
stand-by modus: < 0.5W
max. operation: 240W
Short-term operation: 2 Min.
Lighting: 1.6W LED
Outside lighting: max. 500W
Safety category according to EN 13849-1:
Input STOPA: cat 2 / PLC
Input STOP B: cat 2 / PLC
Internal force limit: cat 2 / PLC
Temperature range: - 20°C - + 60°C
Only for dry locations
Manufacturer: Novoferm tormatic GmbH
Oberste-Wilms-Str. 15a
D-44309 Dortmund
GB
PS
PC