Comelit 2904 Technisches Handbuch Seite 4

wARNING
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for
modifications made by third parties for any reason or purpose, and for the use of non-original accessories and materials.
• All the products comply with the requirements of the 2006/95/CE directives (which replace directive 73/23/CEE and subsequent amendments), as certified by the
CE mark on the products.
• Do not route riser wires in proximity to power supply cables (230/400V).
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians.
TELEPHONE DIRECT CONNECTED TO COMELIT INTERFACE
When a call has been made the phone can be answered. Now you can speak with the visitor.
If you want to open the door, press:
The door will be opened and the connection will be terminated in a few seconds.
When you receive a telephone call while in communication with the visitor a beep will announce you there is a call "behind" your current operation. You can answer this cal by
hang-up the receiver and lift it when the telephone rings. You can do the same if you are in a telephone conversation and a visitor is at the door.
OPTIONAL FUTURES:
A. TELEPHONE CONNECTED DIRECTLy TO THE COMELIT INTERFACE, ALONG wITH A COMELIT DOOR-ENTRy PHONE OR MONITOR
The first receiver used to answer a call from a door-entry phone will begin communicating with the external unit; you will not be able to use any of the other receivers to
answer this call.
B. STANDARD "FOLLOw-ME" FUNCTION USING A REMOTE TELEPHONE OR A MOBILE TELEPHONE
On receipt of a call, answer using the telephone to automatically begin communicating with the visitor. If you wish to open the door, press **. The door will be opened and
communication terminated in the space of a few seconds. In some mobile phones, the ** command is reserved for a different function; in this case you will be able to use
#* to open the door.
C. SPECIAL "FOLLOw-ME" FUNCTION USING A REMOTE TELEPHONE OR MOBILE TELEPHONE, wITH CALL wAITING FROM ExTERNAL UNIT
The installer may set up an alternative "Follow-me" operating mode. In this case, the interface will switch directly to "Follow-me" mode while the telephone rings; you will also
be able to answer using any door-entry phone, monitor or telephone.
When you answer using the telephone in "Follow-me" mode, 3 beeps will sound every 3 seconds. Press button 1 to begin communicating with the visitor; alternatively, press
0 to reject the call.
D. SPECIAL DOOR OPENING
The installer may set up a second door opening procedure. In this case it will be possible to open a second door using the telephone, by means of the on-board relay of
Art. 2904. Door 1, connected to the external unit, can be opened by pressing ** or #*. The other door will be opened at the same time as door 1 (default), or can be opened
independently using just the #* command (see point 5L).
In some mobile phones, the ** code is reserved for different uses; in this case it is possible to use #* only.
1. CONNECTING THE SySTEM:
Connect the interface to the Simplebus system according to the drawings on page 16, 17, 18. The interface is by default set to work on a single family video kit (address
Simplebus 1). If the interface has been installed in a single family video kit you can skip the programming mentioned in step 2.
2. PROGRAMMING THE SIMPLEBUS ADDRESS OF THE TELEPHONE INTERFACE IN 3 STEPS:
Important: An analogue telephone must be connected to the output of the telephone interface.
1 Set the programming dipswitch to the position "ON".
2 Make a call from the entrance panel to the telephone interface. The last number will be stored in the interface. Wait at least for 5 seconds and pick up the receiver of the
analogue telephone and dial:
Hang up the phone.
3 Set the programming dipswitch to the position "1" to enter into the normal mode.
3. PROGRAMMING THE FOLLOw- ME FUNCTION OF THE TELEPHONE INTERFACE IN 3 STEPS:
If the interface is used as a switch between the urban line and the telephone, no programming is needed. If the user wants the follow-me functionality to an external line or a
PABX, it is necessary to program the follow- me function:
Important: An analogue telephone must be connected to the output of the telephone interface.
1 Set the programming dipswitch to the position "ON".
2 Pick up the receiver of the telephone, which is connected directly to the interface, wait for the confirmation beeps and dial ** followed by the number. End the number with **.
Example: In order to program external number 06 -123 456 78 dial:
A pause can be created by dialling an extra ## (wait after each # on a confirmation beep).
3 Set the programming dipswitch to the position "1" to enter into the normal mode.
4 4
A confirmation beep appears.