Service; Storage - Tennant MB12004 Bedienungsanleitung

Machine operation
S Press the drive plate motor switch (2) (right or left) to
start the motor.
S If you raise the shaft (7) slightly, the machine moves
to the right (D).
S If you lower the shaft, the machine moves to the left
(D).
S If you keep the shaft in its central position, the
machine operates on the spot.
S On rough floors, tip the machine (A) before starting
the motor and only then lower it onto the floor.
The machine is equipped with an overload indicator
S
(14) (for excessive pressing force).
S This lamp should not or only briefly light up.
After use
Pull the shaft adjustment lever (5) and set the shaft
S
(7) in its vertical position.
S Now pull the mains plug out of its socket and coil the
electric cable around the handlebar (1) and cable
hook (8).
S To protect the retaining needles, leave the used pad
screwed onto the drive plate until the machine is used
again. Only then replace it with a new pad.
S The ring is fitted with the same procedure but in
reverse order.
Make sure that the ring s two metal pins mate with
S
the recesses in the wheel mounts.
The ring now hangs loosely around the motor unit.
S
S To fit it, its diameter can be enlarged by pulling
between the pins.
Assembly instructions for spray unit
Attach the holding device for the spray can to the
S
shaft (7) with the holder at the top and, when viewed
from the operating position, on the left (G).
S Mount the spray can in the holding device and pivot
the latter back until the ball stop engages.
S Then push the spring buckle over the shaft
adjustment unit (16).
S You can attach the nozzle on the left or right as
preferred (H).
Then point the flexible tube in the desired direction.
S
Operating the spray unit
Equip your machine with the following accessories for cleaner
spraying:
Spray unit and the brown pad.
S
S Fill the spray with the desired product.
S Attach the pad to the drive plate.
S Then start the machine.
S Pull the hand lever on the Spray unit a few times to
spray the cleaner product onto the floor. Start cleaner
spraying immediately, continuing until a gloss is
produced.
S We recommend cleaning the floor section by section.
With the B1 you can clean at a far greater speed than
S
with slower machines.
B1 9002027 (12- -09)
The machine is ideal for cleaning with polymer
S
dispersions. The coating s traffic resistance and
hardwearing properties remain unaffected. Smears
can be removed easily.
Polishing
S For these tasks, we advise using the red pads.
S This is fastest way of removing smears and scratches
and producing the typical wet gloss.

Service

S For repairs, please contact your specialist wholesaler
or one of the service shops.
S You will be expertly and quickly served.
Servicing instructions
The following instructions must always be observed.
S When cleaning and servicing the machine, replacing
parts or when changing over to a different function,
switch off the drive and remove the plug.
The power supply lead must not be damaged by
S
driving over it, crushing, tugging etc.
S Check the power supply lead regularly for signs of
damage.
S The machine must not be used if the power supply
lead is not in perfect condition.
S When using or replacing the power supply or
equipment supply leads, use only those specified by
the manufacturer.
When replacing the plug- -and- -socket connectors of
S
power supply or equipment supply leads, splash
protection and mechanical strength must be assured.
S When transporting the machine in lifts, put the
shaft/bar in a vertical position so that it cannot catch
on the lift walls.
S The shaft/bar is automatically secured against recoil
by the patented shaft/bar adjustment unit.
S Only the spray and cleaning agents suitable for the
machine's purpose may be used.
S Never use highly flammable, combustible, toxic,
health- -hazardous, corrosive or irritant substances.
Repairs, including the fitting of spray agent lines and
S
hoses, may only be carried out by approved customer
service shops or by specialists in this field who are
familiar with all the relevant safety regulations.

Storage

S Remove brush/pad driver from machine and neatly
coil cord around cord hook and handle.
S Store the machine in a dry place and in normal room
conditions (not below under 0_C)
English EN
5