Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8.
. System
m Installa
Se
elect the ch
annel to be
rec
ceiver are s
set to the s
Ch
hannel Sel
lection on
To set the
channel on
(e.g. ballp
point pen). T
activated a
at one time
Camera
set to chan
Ch
hannel Sel
lection on
The receiv
ver can rece
a. Manua
l Channel
Set the
channel on
channe
l always re
camera
and the re
Receiver
set to chan
b. Auto-s
scan Mode
If you w
wish to use
automa
atic scan mo
receive
r. The scan
be scan
nned, simpl
position
n.
Came
era 1
9.
. Trouble
eshootin
If
you obtain
no or a dis
•
Are the po
ower adapte
•
Is the mon
nitor or TV
•
Are the ap
ppropriate c
•
Is there a
microwave
it out of th
he path or r
•
Is the dist
ance betwe
•
Is the rece
eiver anten
10
0.
Tech
hnical sp
Ca
amera
Po
ower Supply
y
Po
ower Consu
mption
Di
mensions (
(on stand)
Op
perating Te
mperature
Im
mage Senso
or
Re
esolution
Le
ns
Mi
n. Illumina
tion
Us
se this dev
vice with o
th
e event of
f damage
09/
/09/2010
AVMOD16
ation
e used on b
both the ca
same chann
nel (1, 2 or
the Came
era
n the came
era, place th
The selecte
ed channel
e.
nnel 1
Camer
the Recei
iver
eive up to t
three came
Selection
n the receiv
ver using a
mains activ
ve. Only on
eceiver are
set to the
nnel 1
Receive
several ca
meras (up
ode. Define
e a channel
n mode will
switch cha
y de-activa
ate it by pla
Ca
amera 2
g
storted pict
ture, check
ers for cam
mera(s) and
switched o
on?
channels se
elected / sw
e oven or ot
ther disturb
relocate ca
mera(s) or
een the cam
mera and th
na position
ned for opti
ecificatio
ons
7.5VDC,
200mA
(included
d)
1.3W
100 x 95
x 40mm
0-50°C ;
32-122°F
1/3" colo
our CMOS
450 horiz
zontal TV li
8mm
8 Lux
original ac
ccessories
or injury r
resulted fr
6N1 - AVM
MOD16CCN
mera and r
receiver. Ma
r 3).
he switch to
o the desire
always rem
mains active
a set to cha
annel 2
eras, even i
n scan mod
pointed ob
bject (e.g.
ne channel
may be act
same chan
nel (1, 2 o
er set to ch
hannel 2
to 3 units)
, you can a
l for each c
camera and
annels each
h 5 seconds
acing the ch
hannel swit
Camera
the followi
ing:
receiver c
orrect (volt
witched on
or off?
bing device
e in the sign
receiver.
he receiver
r greater th
mum recep
ption?
Rece
eiver
Powe
er Supply
Dime
ensions
Oper
rating Temp
Tota
l Weight
Rece
eption Rang
nes
Video
o Output
s only. Vel
leman nv
rom (inco
rrect) use
5
N
ake sure th
he camera a
ed channel
using a po
e. Only one
e channel m
Came
era set to c
de.
ballpoint pe
en). The se
tivated at o
one time. M
r 3).
Recei
iver set to
allow the ch
hannels to
switch on
each chann
s. If you do
not wish a
tch on the r
receiver in
a 3
Rec
tage) and p
properly co
nal path? If
f so, switch
an the tran
nsmission r
7.
.5VDC, 600
(in
ncluded)
11
12 x 62 x 1
perature 0-
-50°C ; 32-
10
05g (0.25L
ge
up
p to 90m (3
1V
Vp-p 75Ω
cannot be
e held resp
e of this de
evice. For
Rev
. 03
and the
ointed objec
ct
may be
channel 3
elected
Make sure th
he
channel 3
run in
nel on the
a camera to
o
to OFF
ceiver
nnected?
h it off, mov
ve
range?
0mA
18mm
-122°F
B)
300Ft)
ponsible in
n
more info
o
n nv
©Velleman
Werbung
