Crown CE10128C Originalbetriebsanleitung Seite 23

Attention: keep in mind that in the pro-
cess of mounting / dismounting of the
drill chuck the screw 12 has a left-hand
thread.
Screwdriver bit / magnetic holder (see fig. 13)
When using the power tool as a screwdriver, use
magnetic holder 14 for reliable locking of screwdriv-
er bits 13 (see fig. 13). A magnetic holder 14 is not
needed for extended screwdriver bits 13 (specially pur-
posed for screwdrivers)�
Initial operating of the power tool
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power tool on / off
Short-term switching on / off
To switch on, press and hold on / off switch 9, to switch
off - release it�
Long-term switching on / off
Switching on:
Push on / off switch 9 and lock it in the position with
lock-on button 8�
Switching off:
Push and release on / off switch 9�
Design features of the power tool
"Impact / drill" switch
Switch 4 is purposed for switching between the follow-
ing operation modes of the power tool:
• drilling, screwing, unscrewing - drilling without
impact in wood, synthetic materials, metal� Screwing
and unscrewing fastening components;
• impact drilling - impact drilling in brick, concrete,
natural stone�
Drilling, screwing, unscrewing:
To switch to this operation mode, move
switch 4 right to the stop�
Impact drilling:
To switch to this operation mode, move
switch 4 left to the stop�
One can switch to another operation mode without
stopping the power tool, simply decrease pressure
applied to it to some extent.
Stepless speed adjustment
Speed is controlled from 0 to maximum by
pressing force of on / off switch 9� Weak
pressing results in low revolutions, which
enable a smooth power tool switch-on�
Speed selector thumbwheel
Use speed control 7 to set required revolutions and
impact frequency�
• Push on / off switch 9 and lock it in the position with
lock-on button 8�
• Set the needed speed�
The required speed is dependent on the material and
can be determined with practical trials�
When operating your power tool at a low speed for a
long time, it has to be cooled down for 3 minutes� To
do it, set a maximum speed and leave your power tool
to run idle�
Changing the rotational directions
Change the direction of rotation only after
a full stop of the motor, acting otherwise
may cause damage to the power tool.
Rotation to the right (drilling, screwing in) - move
the rotational direction switch 6 to the right�
Rotation to the left (unscrewing) - move the rota-
tional direction switch 6 to the left�
Recommendations on the power tool
operation
Drilling (see fig. 14-17)
• Grease the drill bit regularly when drilling holes in
metals (except drilling non-ferrous metals and their al-
loys)�
• When drilling hard metals, apply more force to the
power tool and lower the rotation speed�
• When drilling large diameter holes in metal, first drill
a hole with a smaller diameter and ream it till the nec-
essary diameter (see. fig. 14).
• In order to avoid splitting of the surface at an exit
point of a drill bit when drilling holes in wood, follow the
instructions shown in figure 14.
• In order to decrease dust production when drilling
holes in walls and ceilings, take actions indicated in
fig. 15-16.
• When drilling holes in glazed ceramic tiles, in order
to improve the drill centering accuracy and to save the
glaze from damage, apply adhesive tape to the pre-
sumed hole center and drill after that (see fig. 17). Start
drilling at lower speed increasing it as the hole deep-
ens� Caution: drill tiles in the impactless drilling
operation mode only.
Impact drilling
During the impact drilling, the result does not depend
on the pressure applied to the power tool - this is
caused due to the peculiarities in the impact mecha-
nism design� That is why you should not apply exces-
sive pressure to the power tool - it can jam the drill and
overload the engine�
Screwing the screws (see fig. 18)
• To make fastening of screws easier and in order
to prevent cracking of the work pieces, first drill a
English
23