Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
When filling, always pay attention to the correct air pressure (consult the operating instructions of
your vehicle for information). The compressor is able to supply a pressure of up to 8.3 bar. If the pressu-
re is too high, there is a risk of explosion and injury.
Never allow the compressor to operate for longer than 5 minutes without a pause, otherwise there is a
risk of overheating. Switch the compressor off after 5 minutes of use and allow it to cool down fully (at
least 20 minutes) before starting it up again.
Never leave the compressor to operate unattended
The compressor may discharge the battery of your vehicle if the motor is switched off.
If you use the compressor with the vehicle motor running, ensure good ventilation in the garage or
hall. There is a risk of poisoning!
After filling a tyre, check the tyre pressure again using a separate air pressure tester (e.g. at a filling station, vehicle workshop).
6.2.2 Using the adapter
Open the lock of the valve connection (Figure 5). Insert the appropriate adapter for the required purpose into the valve connec-
tion. Lock the valve connection (Figure 7). Insert the adapter into the filling connection of your leisure equipment (ball, air
bed etc.). Depending on version, it is possible that the adapter will need to be held firmly during the filling process. Now you
can switch on the compressor and start the filling process. When the desired air pressure is reached, switch off the compressor
by pressing the appropriate On/Off switch. Remove the adapter from the valve connection by proceeding in reverse order, as
described above.
6.2.3 Conversion table psi / bar
The units are converted as follows:
1 psi = 0.069 bar
bar
psi
psi
bar
0,7
10
70
0,7
1,4
20
80
1,4
2,1
30
90
2,1
2,8
40
100
2,8
3,4
50
110
3,4
4,1
60
120
4,1
Table 1
6.3 Replacing the fuses
6.3.1 Replacing the fuse for the 12 V system
Rotate the tip (Position 17 in Figure 8) of the 12 V plug (Position 15 in Figure 8) anti-clockwise until it comes away from the plug
and then remove. The fuse (Position 16 in Figure 8) is exposed and can be removed from the plug. Replace the fuse with another
of the same strength and screw the tip back into the plug, Figure 8.
6.3.2 Replacing the fuse for the 230 V system
Open the storage compartment lid on the rear of the device. Remove the connection cable and the air hose. See also Figure 3 in
the overview. Rotate the end cap (Position 18 in Figure 9) and remove. Remove the fuse (Position 19 in Figure 9) from the holder
(Position 20 in Figure 9). Replace it with a new fuse of the same strength. Rotate the end cap back into the holder.
1 bar = 14.504 psi
bar
psi
bar
4,8
70
4,8
5,5
80
5,5
6,2
90
6,2
6,9
100
6,9
7,6
110
7,6
8,3
120
8,3
bar
psi
0,5
1,0
1,5
2,0
2,5
3,0
Table 2
Figure 8: Fuse in 12 V plug
Figure 9: 230 V fuse in storage compartment
bar
bar
psi
7
0,5
3,5
7
15
1,0
4,0
15
22
1,5
4,5
22
29
2,0
5,0
29
36
2,5
5,5
36
44
3,0
6,0
44
psi
bar
ps
51
3,5
58
4,0
65
4,5
73
5,0
80
5,5
87
6,0
9
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
