Virutex CR94D Gebrauchsanweisung Seite 6

on the rating plate.
3. Always keep your hands away from the
cutting area, and always hold the machine by
the handles.
4. Always use original VIRUTEX tools. Never use
tools which are defective or in bad condition.
2. CHARACTERISTICS
Power..........................................................550 W
Motor.......................................................50/60 Hz
Revolutions.........................................30,000/min
Equivalent measured continuous
acoustic pressure level..........................84.1 dB(A)
Customary level of vibrations (hand-arm)..< 2.5 m/s
Bit.............................................D. 38x3.5 standard
Weight........................................................2.5 Kg
3. STANDARD EQUIPMENT
You will fi nd the following items inside the
packaging:
1.- Slotting machine CR94D with hard metal bit of
diameter 38x3.5.
2.- Lateral support included on the machine.
3.- 11 mm key for engine shaft.
4.- 17 mm key for bit shaft.
4. GENERAL DESCRIPTION OF
SLOTTING MACHINE CR94D
The main function of the machine is to slot doors
and windows without dismantling the fi ttings. It is
ideal for the placement of VIRUTEX insulating
joints of thermomeltable rubber and PVC.
It is equipped with a lateral support which enables
the slots to be made faster (Fig. 1).
5. TYPES OF MILLING
The slots must be made at the mobile parts, and
three different types can be distinguished.
1.-Window slot on the drip rail side (Fig. 2).
2.-Window and door slot on the hinge side (Fig. 3).
3.-Window and door slot on the lock side (Fig.4).
6. ADJUSTING THE RABETTING DEPTH
Loosen knob (A) and use the regulation wheel
(B) to adjust the rabetting depth. Tighten knob (A)
once more (Fig. 6).
7. ADJUSTING THE RABETTING HEIGHT
Loosen the securing knobs (D). Use the
regulation wheel (C) to adjust the rabetting height
as indicated in (Fig. 7).
Tighten the securing knobs (D).
8. DIRECTION OF ADVANCE
When making the slots, it is vital that the direction
6
(optional 1840051 D.55x3.5)
of advance of the machine be the same as the
direction of rotation of the bit (Fig.9).
9. CHANGING THE BIT
Loosen the screws (F) and displace the guides
(E) outwards. Loosen screw (G) using a 4 mm
key and the service keys indicated in (Fig. 5 and
Fig. 10). Replace the bit, adjust the guides (E) to
the size of the new bit, and repeat the steps in
reverse order to secure it.
10. JOINTS
The use of PVC and THERMOMELTABLE
RUBBER joints is recommended due to their
2
excellent resistance to weathering and their
good insulation properties in both hot and cold
climates. In addition, they considerably improve
sound insulation against outside noise.
Types of PVC joints:
Profi le
1204040 N9P
1201039 N10P
1204038 N11P
1204037 PL10P
1204036 PL11P
1204041 FP
Types of thermomeltable rubber joints:
Profi le
1204049 N9GT
1204048 N10GT
1204047 N11GT
1204050 FGT
Each type of joint necessitates the use of the
correct bit, depending on the depth required.
In order to place the joints in the slots easily, it
is recommended that JOINT ROLLERS be used
(see table).
JOINT JOINT
MODEL STOCK
N.N9P 1204040 8x3.5
N10P 1204039 10x3.5 10 mm.
N11P 1204038 10x4
PL10P 1204037 8x3.5
PL11P 1204036 8x3.5
FP 1204041 6x3.5
PP 1204042 8x3.5
N9GT 1204049 8x3.5
N10GT 1204048 10x3.5 10 mm.
N11GT 1204047 10x3.5 11 mm.
FGT 1204050 6x3.5
SLOT MIN. ROLLER
N.SIZE RABBET STOCK
10 mm. 1850037
1850037
11 mm. 1850047
10 mm. 1850037
11 mm. 1850047
—- 1850036
—- ——
9 mm. 1850037
1850037
1850047
— 1850036