MC Crypt YTSL-06 Laser Bedienungsanleitung Seite 3

Operating Instructions Operating Instructions
YTSL-06 Laser
Item No. 75 24 76
Intended Use
The laser is intended for generating laser lighting effects and is operated by the built-in controller.
This product may be operated only with the enclosed power supply unit.
The safety regulations and standards for laser operation must be complied with at all times.
The product may be used only in enclosed indoor locations, never outdoors. Contact with mois-
ture, for example in bathrooms, must be avoided.
Any other use than that described above is not permitted and involves additional risks, such as
injuries to the eyes, short circuits and fi re.
No part of the product may be modifi ed or rebuilt, and the housing must not be opened.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Contents
• Laser
• Power adaptor
• Tripod
• Operating instructions
Explanation of Symbols, Inscriptions
This symbol indicates specifi c risks associated with handling, function and use.
Safety Instructions
Read the complete operating manual carefully before using the product, as it
contains important information about the correct installation and operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting da-
mage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! The war-
ranty will be void in such cases!
• This product may be assembled, commissioned and operated only by suitably qualifi ed pro-
fessionals and only in compliance with the requirements stated in this operating manual.
• For safety reasons, any unauthorised conversion and/or modifi cation to the product is not
permitted.
• Use only the supplied mains adapter as a power source.
• Connect the wall plug transformer only to a normal mains socket connected to the public
supply. Before plugging in the power adapter, check whether the voltage stated on the power
adapter complies with the voltage of your electricity supplier.
• Power adapters must never be plugged in or disconnected with wet hands.
• Never unplug the power packs from the mains socket by pulling on the cable; always use the
grips intended for this purpose.
• For safety reasons, always disconnect the power unit from the mains socket during thunder-
storms.
• Adjustments or maintenance should only be carried out by trained professionals who are
aware of the dangers. Improperly executed adjustments might result in dangerous laser radia-
tion.
• When operating the laser equipment, always make sure that the laser beam is directed so that
no one is in the projection area and that unintentional refl ected beams (e.g., from refl ective
objects) cannot be directed into areas where people are present.
• Laser radiation can be dangerous if the laser beam or its refl ection enters unprotected eyes.
Therefore, before using the laser equipment, familiarise yourself with the statutory regulations
and instructions for operating such a laser device.
• Never look into the laser beam and never point it at people or animals. Laser radiation may
result in injuries to the eyes or skin.
• Do not point the laser beam at mirrors or other refl ective surfaces. The uncontrolled, refl ected
Version 10/13
beam may strike people or animals.
• Only operate the laser in an attended area.
• If possible, restrict the range of radiation by using screens or partitions.
• Mark the range of the laser by using barriers or by using warning signs.
• Wherever possible, direct the laser in such a way that it does not cross eye level.
• Caution: if operation settings or procedures other than those described here in these instruc-
tions are used, it could result in exposure to dangerous radiation.
• This product is provided with a Class 2 Laser. Laser signs in different languages are included
in the package. If the sign on the laser is not written in the language of your country, please
affi x the appropriate sign to the laser.
• Never look directly into the laser beam when the device is in operation. The intense light rays
could temporarily impair your eyesight. Moreover, they may trigger epileptic seizures in vulner-
able persons. This applies in particular to epileptics.
• The device is not a toy. Children and adolescents cannot judge the dangers of electrical
devices and lasers.
• Inspect the laser unit for damage from time to time. Should the laser unit or the power adapter
show any damage, disconnect them from the power supply (unplug the power adapter). Do
not use the product afterwards, but take it to a specialist workshop.
• Never pour liquids over electrical devices and never place objects fi lled with liquid on top of
them (e. g. vases). You run the risk of causing a fi re or a fatal electric shock. If liquids enter the
device, immediately disconnect it from the power supply, unplug the power supply unit from
the mains and consult an expert.
• Do not expose the device to high temperatures, dripping or sprayed water, strong vibrations or
heavy mechanical stress.
• Do not place open fl ames, such as burning candles, on or close to the device.
• Do not leave packaging materials unattended. It may become a dangerous plaything for chil-
dren.
• Do not leave the device in operation when it is unattended. For safety reasons, unplug from
the mains socket after each operation.
• Do not use the device in a tropical climate.
• If in doubt about how to connect the product correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical service or another
specialist.
• Also observe any further safety instructions in the individual sections of this operating guide.
Description of the Features
• Producing a starry sky by means of the laser
• Large radiation area
• Green and red laser effect
• Automatic and sound-to-light mode
• Installation on a stand or mounting bracket