Delivery Content; Safety Instructions; Operation - Renkforce 1384397 Bedienungsanleitung

Operating instructions
Shotgun microphone
Item no. 1384397
Intended use
This microphone is designed to convert acoustic signals (sound waves) into
electrical signals. It is designed for all types of recordings such as test recordings,
voice recordings and interviews. The microphone is designed for installation on an
accessory shoe.
You can change the settings for different recording distances using a selector switch.
The low-level audio output signal must only be connected to suitable audio inputs on
computers and other suitably equipped audio devices using a 3.5 mm jack plug.
Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.

Delivery content

• Microphone
• Wind shield
• Microphone holder
• Jack cable (3.5 mm)

Safety instructions

Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• The microphone must only be operated with a battery (1.5 V/DC).
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for a long
period of time to avoid damage through leaking. Leaking or damaged
batteries might cause acid burns when in contact with skin, therefore use
suitable protective gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries
lying around, as there is a risk that children or pets may swallow them.
• Batteries must not be dismantled, short-circuited or thrown into fire.
Never recharge non-rechargeable batteries. There is a risk of explosion!
• When using the product, make sure that the cable is not pinched, kinked
or damaged by sharp edges.
• Coiled jack cable (3.5 mm)
• AA battery
• Operating instructions
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Components and switches
1 2 3
1 3.5 mm jack socket (output)
2 Battery compartment
3 Selector switch
Super / Cardioid / OFF
4 Microphone head
5 Windscreen

Operation

The product must only be connected to suitable audio inputs in order
to avoid distortions or mismatches that could cause damage to the
microphone or the connected audio device. Refer to the connection
information in the "Technical data".
Never direct the microphone at the sound outlet of loudspeakers, as this
can result in feedback which may damage the loudspeakers and the
connected amplifier.
a) Inserting/changing the battery
• Unscrew the cover on the battery compartment (2) in an anticlockwise direction and
then remove the cover.
• Insert the battery (9) into the battery compartment, paying attention to the polarity
markings (plus/+ and minus/-).
• Replace the battery compartment cover. Screw the cover back in place by screwing
in a clockwise direction.
b) Mounting and connection
1. Slide the microphone holder (6) onto a suitable accessory shoe (not included).
2. Click the microphone into the swivel-mounted clip on the microphone holder. Hold
the microphone with the selector switch (3) pointing upwards and press it down
slightly so that it will not fall out of the holder.
3. Ensure that you place the product in a secure position.
4. Adjust the volume to zero on the audio device that you are connecting to the
microphone. If speakers are connected, reduce the volume on these too.
5. Connect the 3.5 mm jack socket (1) on the microphone to the audio device using
the desired jack cable ((7) or (8)).
6. Place the wind shield (5) onto the microphone head (4).
c) Settings on the microphone
1. Turn the microphone on/off using the selector switch (3).
2. Select the recording mode with the selector switch.
The "Super" setting is designed for long recording distances.
The "Cardioid" setting is designed for short recording distances.
Switches the microphone off.
d) Using the microphone
1. Turn on your audio device, e.g. amplifier, speaker or recording device.
2. Turn the sensitivity of your audio device to zero using the corresponding input level
control (refer to the operating instructions of the device you are using).
3. Test the microphone by speaking a few words whilst slowly moving the input level
control on the audio device upwards until the desired output signal level/output
volume is reached.
Air movements such as wind, moving the microphone or breathing create
deep frequencies in the sound spectrum. The attached windscreen (5) (made
of sponge) prevents such sounds from being recorded.
4
6 Microphone holder (not shown above)
7 Jack cable (3.5 mm) (not shown above)
8 Coiled jack cable (3.5 mm)
(not shown above)
9 AA battery (not shown above)
5