Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Table microphone
Item no. 1339075
Intended use
This microphone is designed to convert acoustic signals (sound waves) into electrical
signals. It can be used for announcements, interviews, press conferences or on
lecterns. The flexible gooseneck allows the microphone to be adjusted for different
speaking positions and speakers. The low-level audio output signal must only be
connected to suitable microphone inputs on audio devices.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Microphone
• Windscreen
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• The microphone must only be used on a device with phantom power
(9 - 52 V/DC).
• When using the product, make sure that the cable is not pinched, kinked
or damaged by sharp edges.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
6
5
4
3
2
1
Operation
The product must only be connected to suitable microphone inputs in
order to avoid distortions or mismatches that could cause damage to the
microphone or the connected audio device. Pay attention to the connection
values in the "Technical data".
Never direct the microphone at the sound outlet of loudspeakers, as this
can result in feedback which may damage the loudspeakers and the
connected amplifier.
a) Connection
1. Ensure that you place the product in a secure position.
2. Slide the windscreen onto the microphone head (6).
3. Turn off the audio device to which the microphone will be connected.
4. Insert the XLR connector (4) on the microphone cable into the microphone
connection on your audio device. Use an adapter (not included) if you wish to
connect the microphone using a 3.5 mm jack socket (XLR to 3.5 mm jack socket).
b) Switch positions
ON
ON
OFF
OFF
c) Using the microphone
1. Turn the sensitivity of your audio device to zero using the corresponding input level
control (refer to the operating instructions of the audio device you are using).
2. Turn on your audio device with the connected sound source (loudspeakers).
3. Turn on the microphone using the on/off switch (1) on the stand (7) (move to the
ON position). The LED indicator (2) turns on. Press the switch again to turn off the
microphone (move to the OFF position). The LED indicator turns off.
4. Test the microphone by speaking a few words whilst slowly moving the input level
control on the audio device upwards until the desired output volume is reached.
Air movements such as wind, moving the microphone or breathing create
deep frequencies in the sound spectrum. The attached windscreen (8) made
of sponge prevents such sounds from being recorded.
1 On/off switch
2 LED indicator (concealed)
3 Connection cable
8
4 XLR connector
5 Gooseneck
6 Microphone head
7
7 Stand
8 Windscreen
Werbung
Inhaltsverzeichnis
