Velleman COPERNICUS III Bedienungsanleitung Seite 5

Devi ice 3 - channels
Devic e 4 - channels 1
Devic e 5 - channels 1
• Detaile ed DMX Values
Chann el Fun
1 Cluste
2
3 Pre-pr
Note: Ch annels 1 and 2
• DMX51 12 Connection
Connect an XLR cable to
pin XLR i nput of the VDP
linking ca able should be a
• DMX51 12 Chain with
• DMX51 12 Start Addre
All DMX-c controlled devic
This start t address is the
Enter the e correct numbe
You can u use the same st
device. W When all devices
on one p articular channe
simultane eously. If you s
Changing g the settings of
In the ca se of the 3-cha
VDPL30 0MF5 to 1, the
27.01.201 1
ON N
s 7-9
OFF F
ON N
10-12
OFF F
ON N
13-15
OFF F
s per Channel
nction From F
r groups 0
Sh utter 0
0
6
26
46
66
86
106
rograms
126
146
166
186
206
226
251
will be overridd den when chann
n
o the female 3-p pin XLR output o
PL300MF5. Mu ultiple VDPL300
a two-core scree ened cable with
Termination
A DMX X terminator is r
has to run a long dista
discos ). The terminato
by elec ctrical noise. Th
120Ω resistor betwee
output t socket of the l
Please see illustration
ess
ces need a digita al start address
channel numbe er from which th
er.
tarting address for a whole gro
s have the same e address, all th
el. In other wor ds: changing th
et different add resses, each de
f one channel w will only affect th
nnel VDPL300M MF5, you will h
second VDPL3 300MF5 to 4 (1
VDPL30 0MF5
To Description
255 Different clu
255 From slow to
5 No function
25 Program 1
45 Program 2
65 Program 3
85 Program 4
105 Program 5
125 Program 6
145 Program 7
165 Program 8
185 Program 9
205 Program 10
225 Program 11
250 Chasing thro
255 Sound activa
nel 3 is activated
of your controlle
0MF5s can be li
XLR input and
recommended fo
ance or is in an
or prevents corr
he DMX termina
n pins 2 and 3,
ast device in th
ns.
so that the cor
he device starts
oup of devices o
he VDPL300MF
he settings of on
evice will "listen
he device in que
ave to set the s
+ 3), the third
5
n
uster effects
o fast
ough all program ms
ation mode
d.
er and the other r side to the ma
inked through s serial linking. Th
output connect ors.
or installations w where the DMX
electrically nois sy environment
ruption of the d igital control sig
tor is simply an XLR plug with
which is then p plugged into the
e chain.
rrect device resp ponds to the sig
s to "listen" to th he DMX controll
r enter an indiv vidual one for ev
F5s will "listen" to the control s
ne channel will a affect all device
" to a separate channel numbe
estion.
start address of the first
to 7 (4 + 3) an nd so on.
Rev v. 02
ale 3-
he
cable
(e.g.
gnal
a
e XLR
gnals.
ler.
very
ignal
s
er.
©Vellema an nv