Package Contents; Safety Instructions - Renkforce 1305503 Bedienungsanleitung

G Operating instructions
Alu 13 Port USB 3.0 Hub+Charge
Item no. 1305503
Intended use
The product is designed for connection to a computer with a USB3.0 interface in order
to provide additional USB3.0 ports.
Furthermore, the USB3.0 hub has two separate power outputs that are suitable for
charging suitable devices (e.g. smart phones, or tablets, iPad, etc.).
A standard power unit is used to supply the power.
Always observe the safety instructions and all other information included in these op-
erating instructions.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• USB3.0 Hub
• Power adapter
• Power cable
• USB cable
• Operating instructions
Explanation of symbols
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electrical shock.
This symbol indicates specific risks associated with handling, operation or
use.
The "arrow" symbol points to special tips and operating information.
Safety instructions
D amage due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not disassemble the
product.
• Any maintenance or repair work may only be performed only an expert.
• Do not leave packaging material carelessly lying around, as it could be-
come a dangerous plaything for children.
b) Power adapter/power cable
• The design of the power adapter complies with class II safety require-
ments. Only use a standard mains socket as the voltage source for the
power adapter.
• The mains socket into which the power cable is plugged must be easily
accessible.
• Use only the power adapter supplied to power the USB3.0 hub.
• Do not pull the power plug from the mains socket by pulling on the cable.
• If the power adapter or power cable is damaged, do not touch it; electric
shock carries a risk of danger to life!
First, switch off the mains voltage to the mains socket to which the power
adapter/power cable is connected (switch off at the corresponding circuit
breaker or remove the safety fuse and then switch off at the RCD protec-
tive switch, so that the socket is fully disconnected from the mains volt-
age).
Then you can remove the mains plug from the mains socket. Dispose of
the damaged power adaptor/power cable in an environmentally friendly
way and discontinue use. Replace it by a power supply unit/ power cable
of the same design.
c) Operation
• This product is not a toy. Devices operated on mains voltage should not
be used by children. Therefore, be especially careful when children are
around.
Use the product where it is out of reach of children.
• The product is intended for use only in dry, enclosed indoor locations. No
part of the product should become damp or wet; never handle it if your
hands are wet!
With the power adapter/power cable there is also a risk of a potentially
fatal electric shock!
• When setting up the product, make sure that the cables are neither kinked
nor pinched.
• Do not apply force when connecting the USB plugs. A USB plug fits in the
USB socket only on one of its sides.
• Never use the product immediately after it has been taken from a cold
room into a warm one. The condensation that forms can ruin the product
under certain circumstances. Power supply unit / power cable also have
an associated risk for electric shock!
Allow the product to reach room temperature before connecting it to the
power supply and putting it to use. This may take several hours.
• Prevent the following adverse conditions at the location of installation and
during transport:
- Dampness or excessive humidity
- Extreme cold or heat, direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found in the vicinity of machinery
or loudspeakers
Connection and Start-up
• Connect the circular low-voltage plug of the power adapter into the corresponding
socket of the USB3.0 hub.
• Connect the power adapter to a standard mains socket using the enclosed power
cable.
• Connect the USB3.0 hub via the enclosed USB cable to a free USB3.0 port on your
computer. The computer does not need to be switched off.
• Turn on the USB3.0 hub via the round pressure switch; the blue LED Power lights up.
Upon first use, the operating system will detect the new hardware and automatically
install the required drivers; they are already present in the operating system.
Please note:
When the USB3.0 hub is switched off, all USB ports as well as the two USB
charging ports are non-functional.
• Connect your USB devices to the USB ports labelled "1" to "13" at the USB3.0 hub.
When a USB device has been detected, the corresponding blue LED on the USB3.0
hub lights up.
Of course, you can also connect and use USB2.0 and USB1.1 devices on the
USB3.0 hub.
Depending on the USB device, the operating system detects new hardware and
installs the required drivers. Please refer to the operating instructions of the USB
device to learn how to do this.
For example, Windows already uses its own drivers for many devices, such as for
USB flash drives, USB mice, etc.