Installation - Conrad 80 85 83 Bedienungsanleitung

Connection via WLAN
To connect via WLAN, several settings are required in the menu of the camera.
Therefore the camera must be connected via a RJ45 network cable to your network
first (see previous chapter for the procedure) and to be set up for WLAN operation.
As an example the encoding must be selected, the WLAN-IP address of the camera
etc.
Only then is a WLAN operation possible!
• Like many other WLAN devices the settings depend on the available WLAN hardware and its
configuration.
Based on the multitude of different devices and their configuration a description of
the precise procedure of the installation of the camera is not possible.
The setting of the camera via WLAN as well as the available WLAN devices requires
special network knowledge.
See, for example, the enclosed manufacturer's documentation in English.
• First, connect the camera via a network cable and start the camera's software (see previous
chapter "Getting Started, Connection via RJ45").
After this, you can enter all the settings in the menu option: "Network" or "System".

Installation

After successful start-up, the camera can be installed at the desired location using the mount-
ing bracket provided. The tripod screw underneath the camera can also be used with alterna-
tive bracket types.
Pay attention when drilling and tightening the screws that no cable or pipes are damaged!
The maximum length of the network cable between the camera and router/switch is 100 m.
Only use at least so-called CAT5- or CAT5e cables.
If you use a WLAN connection it is recommended to test the reception first before mounting
the camera.
Proximity to metal parts, cables or electrical/electronic devices have a negative influence on
the camera's range.
The mounting place must be clean, dry and dust-free. Also, installation must not be carried out
in areas where there is a risk of explosion.
Tips & Notes
• If there is a network or system administrator for your network (as will probably be the case in
a larger company), please let this person assume the responsibility for connection and wiring.
Do not connect the camera yourself!
• The image may be focussed by carefully turning the lens.
• In darkness the IR LED automatically switches on; the IR light is not visible by the human
eye. Keep in mind that night vision images may only be displayed in black and white and not
in colour.
• For additional information, see the manufacturer's instructions (either as printed handbook or
as a PDF on the enclosed CD).
Maintenance and cleaning
The product does not require any maintenance and should never be disassembled for any
reason.
To clean the product, use a dry, clean and soft cloth. Before cleaning, disconnect the product
from the power supply; unplug the power adapter from the mains socket.
Clean the lens very carefully to avoid scratch marks.
Do not use aggressive detergents as these might cause discolouration of the casing.
Handling
• Follow the safety instructions in this operating manual and all other information on
installation and operation.
• Never move the camera manually, do not use force! This could damage the pan-
ning and tilting mechanism.
• Use is permitted only in dry indoor locations. The product must not get damp or
wet. There is danger of a life-threatening electric shock!
• Never use the product immediately after it has been taken from a cold room to
a warm one. The condensation that forms might destroy the product. Moreover,
there is danger of an electric shock from the power adapter!
Leave the product switched off and wait until it has reached room temperature
before you use it. This may take several hours.
• Any service or repair work must only be carried out by authorised personnel.
• If the product is not to be used for a while, unplug the power adapter.
• Avoid the following adverse conditions at the installation location and during trans-
port:
- Excessive humidity or dampness
- Extreme cold or heat
- Dust or flammable gases, fumes or solvents
- Strong vibrations
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
• When assembling the device, make sure the cables are not bent or jammed; do
not constrict the pan/tilt mechanism.
Declaration of Conformity (DOC)
The manufacturer hereby declares that this product conforms to the fundamental requirements
and the other relevant regulations of Directive 1999/5/EC.
The Declaration of Conformity for this product can be found at www.conrad.com.
Disposal
Electrical and electronic products do not belong in household waste!
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
Technical data
a) Camera
Operating voltage .........................5 V/DC
Image sensor ................................6.35 mm (1/4"), CMOS
Resolution ....................................640 x 480 Pixel
Camera aperture ..........................60°
Tilting range (vertical) ...................120°
Panning range (horizontal) ...........270°
IR LEDs ........................................10
IR range ........................................Up to 10 m
WLAN ...........................................802.11b/g
LAN ...............................................10/100 Mbit
Installation location .......................Only in dry, enclosed indoor spaces
Dimensions ...................................125 x 101 x 101 (H x W x D, without bracket/antenna)
Weight ..........................................282 g (without bracket/antenna)
b) Power adapter
Operating voltage .........................100 - 240 V/AC, 50 - 60 Hz
Output ...........................................5 V/DC, 2 A
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.