Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
2.5" (6.35 cm) / 3.5" (8.89 cm) Hard drive
enclosure Easy USB 3.0
Item no. 1218047
Intended use
The hard drive enclosure is designed to operate a SATA hard disk drive outside
computer housing. Either a 8.89 cm (3.5") or 6.35 cm (2.5") SATA hard disk drive can be
inserted into the hard drive enclosure. The installed hard disk drive can be operated
as an external computer drive via a USB 3.0 interface. The enclosure is equipped with
an external power supply.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Hard drive enclosure
• Power adaptor
• USB cable
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• If you are not going to use the product for a prolonged period of time,
remove the mains socket from the plug and disconnect the USB cable
from your computer.
• Never move hard disk drives (HDD) when they are in use to avoid damage.
Always wait for at least 30 seconds after turning the product off before
moving it.
• It is intended for indoor use only. Do not use it outdoors. Contact with
moisture, e.g. in bathrooms, must be avoided under all circumstances.
• Use the product only in temperate climates, not in tropical climates.
• In schools, educational facilities, hobby and DIY workshops, the product
is to be operated under the responsible supervision of qualified personnel.
• Before connecting to the mains, make sure that your local AC mains
voltage matches the specifications on the nameplate.
• The power adapter is constructed with protection class II. Only a proper
mains socket (230 V/AC, 50 Hz) of the public supply net must be used as
voltage source.
• Never pour any liquids over electrical devices or put objects filled with
liquid right next to the device. If liquid or an object enters the interior of the
device nevertheless, first power down the respective socket (e.g. switch
off circuit breaker) and then pull the mains plug from the mains socket.
Do not operate the product anymore afterwards, but take it to a specialist
workshop.
• Never use the product immediately after it has been brought from a
cold room into a warm one. The condensation generated could destroy
the product. The plug-in power supply unit also involves danger to life
by electric shock! Allow the product to reach room temperature before
connecting it to the power supply and putting it to use. This may take
several hours.
• If the wall plug transformer is damaged, do not touch it; there is danger
to life from electric shock! First, switch off the mains voltage to the mains
socket to which the wall plug transformer is connected (switch off at the
corresponding circuit breaker or remove the safety fuse, then switch off
at the corresponding RCD protective switch, so that all poles of the mains
socket are disconnected). You can then unplug the wall plug transformer
from the mains socket. Dispose of the faulty wall plug transformer in an
environmentally friendly way; do not use it any more. Replace it with a wall
plug transformer of the same design.
• The mains outlet must be located near to the device and be easily
accessible.
• As power supply, only use the supplied mains adaptor.
• Only connect the power adaptor to a normal mains socket connected to
the public supply. Before plugging in the power adaptor, check whether
the voltage stated on the power adaptor complies with the voltage of your
electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the
cable; always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched,
kinked or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled
in them. This poses a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket
during storms.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
1
2
3.5"
1 Connector cable
3 Status LED
Inserting a hard drive
1. To remove the housing cover, gently press the arrow marker
the cover in the direction of the arrow.
2. Place the enclosure with its feet on the table. Slide the SATA hard disk drive from
the front into the enclosure. Pay attention to the orientation of the hard disk drive
and ensure that the SATA connector (4) on the circuit board is inserted correctly
into the connections on the hard disk drive.
3
4
2.5"
2 USB cable
4 SATA connector
down and slide
Werbung
Inhaltsverzeichnis
