Conrad 55 12 94 Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
Electronic Daytime Switch Timer
Item no. 55 12 94
Intended use
The product uses a socket that can be switched on or off once within 24 hours by means of the
integrated timer. The switched-on period is freely programmable via buttons.
The product should be connected to an earthed mains socket; the mains voltage should be
230 V/AC, 50 Hz.
The power consumption of the consumer connected to the socket of the daytime switch timer
may not exceed 1800 W.
The product may be used only in dry, enclosed rooms.
Always observe the safety instructions included in these operating instructions. Read the oper-
ating manual carefully, keep it in a safe place and / or pass it on to others using the switch timer.
Any use, other than the one described above, may damage the product. Moreover, this involves
hazards such as e.g. short circuit, fi re, electric shock, etc. Modifying or rebuilding any part of
the product is forbidden!
This product complies with the applicable National and European requirements. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
Explanation of Symbols, Inscriptions
This symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specifi c risks associated with handling, function and
use.
☞
The "Hand" symbol indicates special tips and operating information.
The product is only intended to be placed and used in dry and enclosed indoor
rooms; it must not get damp or wet.
Package Contents
• Daytime Switch Timer
• Operating Instructions
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases!
a) In general
• The unauthorised conversion and/or modifi cation of the product is not permitted
for safety and approval reasons (CE). Do not open/disassemble! Contains no
customer-serviceable parts.
Maintenance or repair works must always be carried out by qualifi ed experts who
are familiar with the hazards involved and with the relevant regulations.
• The device is designed according to safety class I. It may be connected and used
only at an earthed mains socket.
• The product is not a toy and must be kept out of the reach of children. Position the
product so it is out of the reach of children.
Be especially careful if children are around. Children cannot see the danger arising
from incorrect use of electrical devices. There is a risk of a life-threatening electric
shock!
• Do not carelessly leave the packaging material lying around since this may be-
come a dangerous toy for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
www.conrad.com
Version 01/12
b) Operation
• The product may be used only in dry, enclosed indoor areas; it must not get damp
or wet! Never place the product in direct vicinity of a bathroom, shower, bathtub or
the like. Lethal hazard due to electric shock!
• Never plug in or unplug the plug-in power unit with damp or wet hands. There is a
risk of a life-threatening electric shock!
• The product must not be exposed to extremes of temperature, direct sunlight or
strong vibrations.
• Do not operate the device in environments where there are high levels of dust,
fl ammable gases, vapours or solvents. There is a danger of fi re and explosion!
• Never connect the device to the power supply immediately after it has been trans-
ferred from a cold room into a warm one (e.g. during transport). The condensation
that develops in such cases could damage the device or cause an electric shock!
Allow the product to reach room temperature. Wait until the condensation has
evaporated. This might take several hours. Only after this should the product be
plugged in to the power supply and put into use.
• Ventilators, heaters, heat fans or heaters with open elements should never be left
unattended. We recommend that you do not connect such devices to the switch
timer. Fire hazard!
• Always pull the plug of a device connected to the switch timer out of the switch
timer's socket only at the appropriate gripping surfaces; never pull the plug out by
the fl ex!
• Do not overload the switch timer. Observe the maximum connected load in the
chapter "Technical Data".
• Do not connect in series! This can lead to an overloading of the switch timer! Fire
hazard!
• Do not operate while covered! At higher connected loads, the switch timer
becomes warm, which can lead to overheating and potentially a fi re if covered!
• Current-free only when the plug is withdrawn!
• Do not operate the product if it is damaged. There is a risk of a life-threatening
electric shock!
In this case, dispose of the product environmentally correctly.
A safe operation can no longer be assumed, if:
- the product shows visible signs of damage,
- the product does not work at all or does not work correctly (leaking smoke or a
smell of burning, audible crackling noises, discolouration to the product or the
adjacent surfaces)
- the product was stored under unfavourable conditions,
- it was exposed to heavy loads during transport
• Always pull the switch timer out of the mains socket before cleaning it or when the
device will not be in use for a long time.
• Only use the appliance in a moderate climate, never in a tropical climate.
• Never pour any liquids on or next to the product. It can cause fi re or perilous elec-
tric shock danger. If any liquid has still managed to enter the device, immediately
turn off the power supply to the mains socket at which the switch timer is con-
nected (turn off the fuse / circuit breaker / residual current operated circuit breaker
of the associated circuits). Only then should you pull the switch timer out of the wall
socket and take it to a specialist. Do not operate the device anymore.
• In commercial institutions, the accident prevention regulations of the employer's
liability insurance association for electrical systems and operating facilities are to
be observed!
• If you have any questions that are not answered in this manual, please contact our
technical service or another specialist.