Installation - Renkforce 1034034 Bedienungsanleitung

c) Reset the wireless doorbell
You can pair a maximum of 4 converters with the wireless doorbell. In case you have already
paired 4 converters with the wireless doorbell and you want to replace one of the converter with
a new one, proceed as follows:
• Reset the wireless doorbell, otherwise you cannot pair further converters. To do so remove
the batteries from the wireless doorbell. Wait approx. 10 seconds before putting the batteries
back in.
• Then pair all converters again with the wireless doorbell.
d) Use several wireless doorbells
The wireless doorbell set can be expanded with several more wireless doorbells (not supplied).
Once you have started up the wireless doorbell set, insert the batteries into the additional wireless
doorbell to be added. Hold the LR button (7) for approx. 4 seconds. Activate the converter within
10 minutes. The wireless doorbell is able to save the frequency.
Due to the signal processing time of the wireless doorbells, the ring tone of the
individual wireless doorbells is emitted with a slight time delay (max. 2.5 seconds).

Installation

The range between the converter and wireless doorbell depends on the surrounding
conditions. Normally it is possible to run this device without a problem in a detached
house. We recommend that you check that the product functions correctly before final
installation.
When drilling or screwing, make sure that no cables or wires are damaged. Danger of
electric shock and injury!
a) Converter
Place the converter directly next to the sound source (max. 20 mm away).
Also be aware that the converter can react to other acoustic influences such as dog
barks or loud surrounding noises.
• Attach the converter using the supplied screws and dowels to a smooth, dust-free surface.
• Remove the mounting plate (11) from the reverse of the converter by pushing it down.
• Use the mounting plate as a template and mark the position of the two screw holes on the
installation surface.
• Drill the two holes in the wall and insert the dowels.
• Mount the mounting plate with the two screws onto the surface. The countersunk drill holes in
the mounting plate have to point away from the mounting surface.
Depending on the mounting surface, it is recommended to insert washers between the
mounting surface and the mounting plate. This prevents the converter and wireless
doorbell getting scratched during installation.
• Place the converter on the mounting plate and push it down. The converter must audibly lock
into place.
b) Wireless doorbell
• Attach the wireless doorbell in the same way as the converter on a smooth, dust-free surface.
• Alternatively you can place the wireless doorbell on a stable, even surface.
Settings
a) Sensor sensitivity
• To make sure that the converter works properly, adjust it to your sound source.
• Open the battery compartment (14) of the converter.
• Turn the setting switch for the sensor (13) anti-clockwise using a small cross-head screwdriver
to reduce the sensor sensitivity. Turn the setting switch clockwise to increase the sensor
sensitivity.
b) Ring tone
• You can choose from 8 different ringtones: 1. Ding Dong Dong, 2. Ding Dong, 3. Dog bark,
4. Fanfare, 5. Telephone ring, 6. Melody, 7. Westminster, 8. Saxophone
• Open the battery compartment of the converter.
• To change the ringtone click on the Sound button (12). The wireless doorbell emits the ring tone
via its speaker (3). Repeat this process until the desired ring tone is played back.
Reduce the sensor sensitivity when setting the ring tone. Otherwise the ring tone itself
may activate the sensor in the converter. In this situation the wireless doorbell would
continue to emit the same ring tone.
c) Volume
• Open the battery compartment (8) on the reverse of the wireless doorbell.
• Set the desired volume using the volume control (5):
Hi = high volume; Med = medium volume; Lo = low volume
d) Bell/flashlight
• Open the battery compartment on the reverse of the wireless doorbell.
• You have 3 options which you can select using the slide switch (6).
• Switch setting Bell: The flashlight is switched off and is not activated when the converter is
activated. Only the set ring tone is emitted.
• Switch setting Flash: The flashlight is switched on and is triggered when the converter is
activated. In the setting a ring tone is not emitted.
• Switch setting Bell+Flash: The flashlight is switched on and is triggered when the converter is
activated. In addition the set ring tone is also emitted.
Range
The range of the wireless signal transmission between the converter and a wireless doorbell is
up to 150 m.
This figure, however, refers to the distance between a converter and a wireless
doorbell which are within sight of each other and where there are no interfering
influences. In practical situation, there are usually walls, ceilings etc. between the
converter and the wireless doorbell, which correspondingly reduce the range. Due to
the different influences on the radio transmission it is unfortunately not possible to
guarantee a particular range. Normally, however, it is possible to use this in a detached
house without a problem.
The range may be reduced by the following:
• Walls, reinforced concrete ceilings
• Coated or metallised insulating glass
• Nearby metallic and conductive objects (e.g. radiators)
• Human bodies in the area
• Broadband disturbances, e.g. in living areas (DECT telephones, mobile phones, wireless
headphones, baby monitoring systems etc.)
• Nearby electric motors, transformers, power adaptors and computers
• Computers or other electronic device which are badly shielded or in operation
Maintenance and cleaning
• The product is maintenance-free apart from any change of battery that may be necessary, and
occasional cleaning.
• Use a clean, dry and lint-free cloth for cleaning. When cleaning, do not apply too much force to
the surface, so that you avoid scratches. Dust is very easy to remove with a clean, long brush
and a vacuum cleaner.
• Under no circumstances should you use aggressive cleaning agents, alcohol or other chemical
solutions, as they can damage the casing.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EC.
The Declaration of Conformity for this product can be found at www.conrad.com.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Remove any inserted (rechargeable) batteries and dispose of them separately from
the product.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/
rechargeable batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labelled with this symbol to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals
involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable)
batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores
or wherever (rechargeable) batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
a) Converter
Power supply ...................................... 2 x 1.5 V/DC batteries, type AA / Mignon
Transmission frequency .................... 433 MHz
Range ................................................... up to 150 m (converter <—> wireless doorbell; free-field)
Dimensions (W x H x D)..................... approx. 66 x 90 x 22 mm
Weight .................................................. approx. 62 g
b) Wireless doorbell
Power supply ...................................... 2 x 1.5 V/DC batteries, type C / Baby
Transmission frequency .................... 433 MHz
Dimensions (W x H x D)..................... approx. 92 x 143 x 36 mm
Weight .................................................. approx.. 165 g
c) General
Operating conditions ......................... 0 to +40 °C, 10 - 80 % relative humidity
Storage conditions............................. 0 to +60 °C, 10 - 80 % relative humidity
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE. V1_0214_02-KV