Operation; Technical Data; Care And Cleaning; Declaration Of Conformity (Doc) - Sygonix 1553977 Bedienungsanleitung

Operation

a) Programming a receiver
Ensure that no other transmitters or sources of interference are sending signals
when you are programming the receiver, otherwise the receiver may not program
properly.
You can add an unlimited number of receivers to each channel.
Proceed as follows:
• Press the function button (1) to select a channel. The blue LED indicates the selected
channel. Press the function button again to select the other channel. This channel is indicated
by the red LED.
• Place the receiver that you want to program in programming mode. Programming mode
should be enabled for approximately 15 seconds, although this may vary between devices.
Refer to the device's operating instructions for details.
• After enabling programming mode on the receiver, hold down the function button (1) on the
transmitter until the LED indicator (3) starts to flash quickly. This indicates that programming
mode is enabled on the receiver. The transmitter sends a signal to the receiver when you
hold down the function button (1).
• Keep holding down the function button until the device connected to the switch turns on. If the
receiver fails to add the transmitter, release the function button to exit programming mode.
• Programming mode will be disabled automatically when the receiver has added the
transmitter.
• Repeat these steps in the same order to program other receivers.
b) Function test and normal operation
• Once you have programmed the receiver, use it in accordance with its operating instructions.
If the device connected to the receiver turns on when you press the switch, this indicates that
the wireless switch system is functioning properly.
• When the switch system is turned on, the transmitter sends a signal to the receiver when
you press the wall switch. This signal is then used to turn the connected device on and off.
c) Deleting preprogrammed transmitters
• If you do not want a receiver to respond to the transmitter (e.g. if you want to use the
channel for another RSL transmitter), you can delete the transmitter accordingly. Refer to the
receiver's operating instructions for details.
• Repeat the same steps to delete the transmitter from other receivers.
• You do not need to change the settings on the transmitter. After deleting the transmitter, you
can program other receivers as normal.
d) Changing the battery
Replace the battery when the transmitter stops working or when you notice a significant drop
in the range. Replace the battery with a new one of the same type (CR2477). To change the
battery, proceed as follows:
• Carefully push the two halves of the casing apart with your fingernails or a flat screwdriver.
• The two halves of the casing are held together by small tabs. At least two of the three tabs
must be pressed in order to open the casing. Be careful not to break the tabs when opening
the casing.
• Remove the used battery.
• Insert a CR2477 battery in the correct polarity. The positive pole (+) must be placed on the
round hole on the lid.
• Place the two halves of the casing onto the circuit board contacts (with the battery in the
battery compartment) and carefully press them together until the tabs click into place.
• Ensure that all of the cables protruding from the transmitter are placed in the correct inlets
and are not squashed.

Care and cleaning

• The product is maintenance free (apart from changing the battery). Never attempt to
disassemble the product, apart from separating the two halves of the casing. Repair and
maintenance work must be done by a technician.
• Before cleaning the product, disconnect it from the power supply by removing the battery.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this
product conforms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a flag symbol, and then enter the product order
number in the search box. The EU Declaration of Conformity is available for
download in PDF format.
Disposal
a) Product
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
If a battery is inserted, remove it and dispose of it separately from the product.
b) Batteries
You are required by law to return all used batteries. They must not be placed in
household waste.
Batteries that contain hazardous substances are labelled with this symbol to indicate
that disposal in domestic waste is forbidden. The abbreviations for heavy metals in
batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery,
e.g. below the waste icon on the left).
Used batteries can be returned to local collection points, our stores or battery retailers.
You thus fulfill your statutory obligations and contribute to the protection of the environment.

Technical data

Battery .......................................... CR2477
Battery life ..................................... At least 3 years
Transmission frequency................ 433.92 MHz
Transmission power...................... Less than 10 dBm
Wireless range .............................. Approx. 70 m (with no obstructions)
Operating/storage conditions ........ 0 to +45 °C, 0–90 % relative humidity (non-condensing)
Dimensions (W x H x D) ............... 41 x 41 x 15 mm
Weight .......................................... 26.5 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1553977_v1_1017_02_DS_m_4L(1)