Renkforce BM-88P Bedienungsanleitung Seite 3

Version 02/13
O P E R A T I N G I N S T R U C T I O N S
BM-88P Waterproof Bluetooth
Shower Speaker
Item no. 35 24 07
Intended use
The waterproof Bluetooth® shower speaker is used for music playback via coupled Bluetooth®
devices. It also features a built-in Bluetooth® speakerphone.
Power is supplied by the built-in rechargeable battery. This may be charged only via a suitable
USB connection.
Devices that are equipped with a USB charging or power supply socket can be charged or oper-
ated with the additional USB output.
The speaker is resistant to strong sprays of water but may not be submerged in water.
Any other use than that described above, could lead to damage to this product and involves the
risk of short circuits, fi re, electric shock, etc.
No part of the product may be modifi ed or rebuilt, and the housing must not be opened.
This product complies with the applicable national and European requirements.
Always observe the safety instructions!
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions. We do not assume any liability for any resulting
damage.
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
In the operating manual, an exclamation mark inside a triangle indicates impor-
tant instructions.
The "hand" symbol indicates special information and advice on operating the
device.
• For safety reasons, any unauthorised conversion and/or modifi cation to the product is not
permitted.
• The speaker's rechargeable battery may be charged only via a suitable USB connection.
• Do not immerse the speaker in water or other liquids.
• Do not expose the speaker to high temperatures, strong vibrations or heavy mechanical loads.
• Inspect the speaker from time to time for damage. If it shows damage, do not use it anymore
and take it to a specialist workshop.
• Do not place open fl ames such as burning candles on the device or in its immediate vicinity.
• Use the device only in temperate climate regions and not in tropical ones.
• This product is not a toy; it is not suitable for children. Children are not aware of the potential
dangers involved when using electrical devices.
• Do not leave packaging materials unattended. It may become a dangerous plaything for
children.
• If you have doubts about how the equipment should be operated or how to connect it safely,
consult a trained technician.
• Also observe any further safety instructions in the individual sections of this operating guide.
Controls and Parts
Connection panel
(1) Charge display
(2) Main switch
®
(3) Connection USB IN 5V
(4) Connection USB OUT
Operating panel
(5) Phone button
(6) REW button
(7) PLAY/PAUSE button
(8) Battery display
(9) – button
(10) Microphone
(11) FF button
(12) LED display
(13) + button
(14) ON/OFF button
Operation
Recharging the Battery
Prior to initial operation, the built-in rechargeable battery must fi rst be charged. Charging takes
about 4 hours.
• Open the cover of the connection panel on the back.
• Connect the included USB cable to the USB IN 5V port (3).
• Plug the other end of the USB cable into the USB connection of a computer or into a suitable
• The charge display (1) lights up red during the charging process and changes to green as
• Unplug the USB cable again after the charging process and close the cover of the connection
• The operating time with one battery charge is, depending on the volume and use, up to 25
• When the battery needs to be recharged, the battery display (8) lights up.
Switching on or off
• Open the cover of the connection panel on the back.
• Move the main switch (2) to the ON position to switch on the power supply of the device.
• Close the cover of the connection fi eld again to ensure the protection against moisture.
• Press and hold the ON/OFF button (14) for 3 seconds, until a signal tone sounds and the LED
• After the speaker is turned on, the blue display fl ashes twice every 2 seconds.
• To turn the device off again and switch to Standby mode, press and hold the ON/OFF button
• To switch the device off completely, move the main switch (2) back to the "OFF" position.
Pairing
Before it is possible to transmit between your Bluetooth® device and the speaker, both devices
must be coupled with each other. This process is called "pairing".
• Turn on your Bluetooth® device with which the speaker is to be coupled, and activate pairing
The USB connection at which the device is charged must have a power rating
of at least 500 mA. This is normally assured at every USB connection of com-
puters.
USB power supply.
soon as the built-in rechargeable battery is completely charged.
panel again to ensure the protection against moisture.
hours.
display (12) briefl y lights up red and then fl ashes blue.
(14) again for 3 seconds, until a signal tone sounds and the LED display (12) turns red and
then turns off.
The device switches off automatically after being idle for 10 minutes.
The speaker has to be switched off at fi rst for the pairing process.
mode here (for more information, see the instruction manual of the corresponding device).
Now the device searches for Bluetooth® devices in the reception range.