Connections On The M8 Rear Panel; Rc 2 Remote Control - Quadral AURUM M8 Bedienungsanleitung

Note:
If this display will flash the protection circuit turn off speaker in case of failure or
overload. Reset will be possible if you operate power switch (9) located at back
panel again.

Connections on the M8 rear panel

14 13
Right
+ +
Mono
A B
Balanced In Unbalanced In
AURUM
Right Left
Left
quadral GmbH & Co. KG - Am Herrenhäuser Bahnhof 26-28 - D-30419 Hannover
Right
Mono In Mono In
1 2 3
1 Balanced In Balanced XLR Inputs
2 Unbalanced In
Stereo inputs
3 RCA Stereo inputs that may also be used as outputs
4 RCA / XLR
Operating mode switch to forward the input signals (2)
for inputs 1 – 3
5 Mono / Stereo
Operating mode switch
6 Gain
Multi-stage switch used to adjust the input sensitivity.
(+3dB / 0dB / -10dB). Please mind the information pertaining
to the installation/startup.
7 Link In
Input for the 12V control connection of the P8
pre-amplifier
8 Link Out Output socket used to forward the control voltage to other
devices
9 Power switch Completely disconnects the device from the power
supply
10 Power supply socket
11 Loudspeaker output A (Left Channel)
12 Loudspeaker output B (Left Channel)
13 Loudspeaker output B (Right Channel)
14 Loudspeaker output A (Right Channel)
20
12 11
Left
DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
+ +
Mono+
CAUTION ACHTUNG
RISK OF ELECTRIC SHOCK STROMSCHLAG GEFAHR
DO NOT OPEN NICHT ÖFFNEN
ATTENTION ATENCIÓN
RISQUE DE CHOC ELECTRIQUE RIESGO DE DESCARGA ELCTRICA
NE PAS OUVRIR NO ABRIR
TO REDUCE THE RISK OF ELECTRICAL SHOCK OR FIRE, DO NOT
B A
EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN.
® Handmade in Germany
On
Link
max. Power Consumption: 1,2kW
Fuse:
100V / 115V: T6.3, A L250V
In Out
230V:
RCA / XLR Gain
+3 / 0 / -10 dB
Mono / Stereo
4 5 6 7 8
Note:
If the buttons 4, 5 and 6 are pressed, there is a pause of about 5 seconds until all
operating points can be stabilized and the signal is released/cleared.
The AURUM amplifiers P8 / M8 / A5 / A3 and the AURUM CD players C3 / C5 / C5 DA
may be individually controlled using the RC-2 System Remote Control.
10
Important note:
If you want to remotely control the amplifier or CD player functions, you must use
the SELECT button to select the relevant operating mode beforehand.
Off
T3.15, A L250V
Select
AMP CD
Amplifier operation
9
1 SELECT button
2 ON / OFF button
3 MUTE
4 Volume - minus
5 Volume - plus
6 Left balance
7 Balance plus
8 Signal source
downwards
9 Signal source
upwards
14 Level setting (for
each input using
buttons 4 & 5)
15 Display brilliance
RC 2 Remote Control (OPTIONAL)
Select
AMP CD
1
2
3
4
L R
6
8
10
12
Repeat Random Prog.
15
Display Opt.
RC-II
Select
AMP CD
CD operation
5
1 SELECT button
2 ON / OFF button
7
3 MUTE
4 Stop
9
5 Repeat / Pause
11
6 Search backwards
13
7 Search forwards
14
8 Scan backward
through the titles
16
9 Scan forward
through the titles
10 File down
11 File forward
12 Repeat (title / all)
13 Shuffle
15 Display brilliance
16 Unassigned
(optional)
21