OK. OPD 250 Gebrauchsanweisung Seite 23

CONGRATULATIONS
Thanks for your purchase of an ok. product. Please read this manual carefully and keep it for future
reference.
IMPORTANT SAFETY INSTRUCTIONS. READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
Risk of electric shock! Do not open.
1.
CAUTION: To prevent the risk of electric shock, do not remove cover (or back). No user-serviceable
2.
parts inside. Refer servicing to authorised service agent.
3. For safety reasons, this class II device is provided with double or reinforced insulation as
indicated by this symbol.
4. The lightning flash with arrowhead within an equilateral triangle is intended to alert the user
to the presence of uninsulated "dangerous voltage" inside the enclosure of this device, which
may be of sufficient magnitude to constitute a risk of electric shock to persons.
5. The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance instructions in the literature
accompanying this device.
DANGER! Invisible laser radiation when open and safety interlock failed or defeated. Avoid
6.
direct exposure to the beam. Do not touch the lens.
7. Before connecting the device to a socket outlet, make sure the voltage indicated on the device
corresponds to your local mains.
8. The mains plug or device coupler is the disconnecting device. It shall remain readily operable.
If the supply cord is damaged, it must be replaced by the manufacturer or its authorised service
9.
agent or similarly qualified person in order to avoid hazard.
WARNING! To reduce the risk of fire or electric shock, do not expose this device to rain or moisture.
10.
Protect from dripping or splashing. Do not place any objects filled with liquids, such as vases, on
the device.
11. Regularly check if the supply cord, device or extension cable are defective. If found defective, do
not put device into operation. Immediately pull the plug.
12. Place the supply cord and, if necessary, an extension cable in such a way that pulling or tripping
over it is impossible. Do not allow the supply cord to hang down within easy reach.
13. Do not jam, bend or pull the supply cord over sharp edges.
14. Protect the supply cord from being walked on or pinched particularly at the plug, convenience
receptacles and the point where it exits from the device.
15. Never pull the plug by the supply cord or with wet hands.
16. Disconnect the mains plug in case of faults during use, during lightening storms, before cleaning
and when not using the device for a longer period of time.
In case of malfunction due to electrostatic discharge, reset the device by removing the mains plug
17.
from the socket outlet.
Refer all servicing to authorised service agent. Do not attempt to repair the device yourself.
18.
Servicing is required when the device has been damaged in any way, such as the supply cord or
plug are damaged, liquid has been spilled, objects have fallen into the device, the enclosure is
damaged, the device has been exposed to rain or moisture, does not operate normally, or has been
dropped.
19. The product is only suitable for use at moderate degrees of latitude. Do not use in the tropics or in
particularly humid climates.
20. When installing the device, leave sufficient space for ventilation. Do not install in bookcases, built-in
cabinets or the like.
21. Do not impede ventilation by covering the ventilation openings with items, such as newspapers,
table-cloths, curtains, etc. Do not insert any objects.
22. Do not place naked flame sources, such as lighted candles, on the device.
23. Do not place any electronic equipment or toys on the device. Such items could fall from the top and
cause device damage and/or personal injury.
24. Do not install near any heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
25. Do not apply excessive force to the front or top, as this could ultimately overturn the device.
26. Do not shift or move the device when powered on.
IM_OPD250_171227_V03_HR.indb 23
23
EN
27/12/17 2:26 pm