Using The Appliance - Clatronic DR 3280 Bedienungsanleitung

Connected Wattage
The station has a total maximum wattage of 1500 W.
CAUTION: Overload!
• If you use extension leads, these should have a cable
cross-section of at least. 1.5 mm².
• Do not use any multiple sockets, as this appliance is
too powerful.

Using the Appliance

CAUTION:
Before you begin cleaning you should test the materials to
be cleaned as to their suitability for cleaning with steam.
Do not hold the steam nozzle for too long and too close in
one position.
After you have filled the kettle with water and selected a
cleaning attachment, please proceed as follows:
Lock the steam switch (21) to prevent pressing it inadvertently.
1. Turn the lock (22) on the steam pistol (20) to OFF / LOCK
without the steam switch (21) pressed in (Fig. A).
2. Connect the appliance to a duly installed protective
contact socket.
3. Press the on / off switch (4) (Fig. D). The red control lamp
(3) lights up. The temperature control lamp (2) shows that
the appliance is heating up.
4. After approx. 12 min the steam temperature has been
reached and the temperature control lamp (2) goes off.
The appliance is ready for operation. During use this con-
trol lamp shows that the water is being heated up again.
WARNING:
If the steam switch is pressed while the orange lamp is on,
it is possible for hot water to be ejected from the nozzle.
5. For the purposes of cleaning turn the lock (22) on the
steam pistol (20) to ON (Fig. B1).
WARNING:
• Before cleaning, always remove the mains plug and wait until the
appliance has cooled down.
• Do not immerse the appliance in water. Otherwise this might result
in an electric shock or fire.
CAUTION:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
38
DR3280_IM_new2
6. Point the steam nozzle at the surface to be cleaned and
press the steam switch (21) (Fig. B2).
NOTE:
During operation please ensure that the hose does not
become twisted or squashed.
Filling up the Water Boiler when Using the Appliance
If there is no more water inside the kettle no steam is emitted
when the steam switch (21) is pressed. The water has to be
filled up as follows:
1. Press the on / off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket!
3. Release the residual pressure with the steam switch (21)
(see "Initial Operation", points 2 and 3).
WARNING: Danger of Injury!
Please open the safety lock (6) only when no more
steam comes out of the nozzle.
4. Slowly open the safety lock (6) and wait a few seconds
before opening it completely until the overpressure has
been released.
5. Fill freshwater from the measuring beaker (15) into the
kettle. Take care of water splashes that might come out
of the boiler. In order to avoid water spray, please use the
funnel supplied (Fig. C). Fill the water in slowly. Do not
overfill! Max. water capacity: 1.5 litres.
6. Fasten the safety lock again.
7. Reinsert the plug into the socket and switch on the appli-
ance using the on / off switch.
When You Have Finished Using the Appliance
1. Press the on / off switch (4). The red control lamp goes off.
2. Remove the mains plug from the socket!
3. Release the residual pressure with the steam switch (21)
(see "Initial Operation", points 2 and 3).
4. Allow the appliance to cool down for approx. 1 hour
before you put it away.
Cleaning
• Before the appliance is put away or cleaned it must have
completely cooled down.
• The appliance and accessories should only be cleaned
with a slightly damp cloth.
10.07.18