EuroLite DXT-TSP PRO Bedienungsanleitung Seite 2

DXT-TSP
PRO
DMX Truss Splitter
No. 70064865
USER MANUAL
EN
Welcome to Eurolite! Your new DXT-TSP PRO is part of Eurolite's DXT series, which
consists of high-performance and reliable DMX tools made in Germany. The DXT-TSP
PRO is designed for splitting a DMX512 control signal into two separate data lines. The
unit features a Neutrik PowerCon input and feed-through output, 3-pin XLR connectors, a
status LED and a clamp for 50 mm crossbeams.
SAFETY WARNINGS
Please read these instructions carefully before using the product. They contain
important information for the correct use of your product. Please keep them for future
reference.
Intended use
This product distributes control signals and is intended for commercial use.
Only use the product according to the instructions given herein. Damages due to
failure to follow these operating instructions will void the warranty! We do not assume
any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the
warranty/guarantee will be null and void.
Unauthorized rebuilds or modifications of the product are not permitted for reasons of
safety and render the warranty invalid.
Danger due to electricity
The product is suitable for indoor use only. Do not use it outdoors. Never expose it to
rain or moisture. Do not store it in rooms exposed to moisture.
The product is supplied with hazardous mains voltage. To reduce the risk of electric
shock, do not open any part of the product. There are no serviceable parts inside the
device.
Only connect the device to a properly installed mains outlet. The outlet must be
protected by residual current breaker (RCD). The voltage and frequency must exactly
be the same as stated on the device. If the mains cable is equipped with an earthing
contact, then it must be connected to an outlet with a protective ground. Never defeat
the protective ground of a mains cable. Failure to do so could result in damage to the
device and possibly injure the user.
Caution! Never touch the plug's contact pins shortly after unplugging the unit (danger
of electric shock).
The mains outlet must be easily accessible so that you can unplug the device quickly if
need be.
Never touch the mains plug with wet or damp hands. There is the risk of potentially
fatal electric shock.
The mains cable must not be bent or squeezed. Keep it away from hot surfaces or
sharp edges.
Never pull the mains cable to disconnect the mains plug from the mains outlet, always
seize the plug.
Unplug the device during lighting storms, when unused for long periods of time or
before cleaning.
Do not expose the device to any high temperatures, direct sunlight, dripping or
splashing water, strong vibrations or heavy mechanical stress.
Do not place any objects filled with liquids on the device.
Do not place any open sources of fire, such as burning candles, on or directly next to
the device.
Make sure that objects cannot fall into the device, in particular metal parts.
Only have repairs to the device or its mains cable carried out by qualified service
personnel. Repairs are required when the device or the mains cable is visibly
damaged, liquid has been spilled or objects have fallen into the device; when the
device has been exposed to rain or moisture, has been dropped or malfunctions occur.
Danger to children and people with restricted abilities
This product is not a toy. Keep it out of the reach of children and pets. Do not leave
packaging material lying around carelessly.
This device may be used only by persons with sufficient physical, sensorial, and
intellectual abilities and having corresponding knowledge and experience. Other
persons may use this device only if they are supervised or instructed by a person who
is responsible for their safety.
Eurolite is a brand of Steinigke Showtechnic GmbH • Andreas-Bauer-Str. 5 • 97297 Waldbüttelbrunn, Germany
Warning – risk of injuries
Make sure that the product is set up or installed safely and expertly and prevented from
falling down. Comply with the standards and rules that apply in your country.
For commercial use the country-specific accident prevention regulations of the
government safety organization for electrical facilities must be complied with at all times.
If you lack the qualification, do not attempt the installation yourself, but instead use a
professional installer. Improper installation can result in bodily injury and or damage to
property.
The manufacturer cannot be made liable for damages caused by incorrect installations
or insufficient safety precautions.
For overhead use, always secure the device with a secondary safety attachment such as
a safety bond or safety net.
Make sure that the area below the installation place is blocked when rigging, derigging or
servicing the device.
INSTALLATION
WARNING! Risk of injury caused by falling objects. Devices in overhead
installations may cause severe injuries when crashing down. Make sure that
the device is installed securely and cannot fall down. The installation must be
carried out by a specialist who is familiar with the hazards and the relevant
regulations.
The device may be placed on the floor or fastened to a truss or similar rigging structure.
The device must never be fixed swinging freely in the room. The rigging structure must
support at least 10 times the weight of all fixtures to be installed on it.
Secure the device with a safety bond or other secondary attachment. This secondary
safety attachment must be sufficiently dimensioned in accordance with the latest
industrial safety regulations and constructed in a way that no part of the installation can
fall down if the main attachment fails. Pull the safety bond through the bracket and fasten
it in such a way that, in the event of a fall, the maximum drop distance of the device will
not exceed 20 cm.
After installation, the device requires inspections periodically to prevent the possibility of
rot, deformation and looseness.
Make all data and power connections. The status indicator will light up green when a
DMX signal is present.
DATA AND POWER CONNECTIONS
Connect data cables coming out of your lighting control device to the DMX IN jack and
your DMX fixtures to the DMX OUT jacks. All jacks are galvanically isolated. The status
indicator will light up green when a DMX signal is present.
Connect the cable provided to the POWER IN jack and to a mains socket. If necessary,
connect the supply line of your DMX fixtures to the POWER THROUGH jack. This feed-
through output is wired in parallel with the power input and accepts a maximum load of
16 A.
CLEANING AND MAINTENANCE
Cleaning of the device is limited to the surface. Only wipe off the product with a soft lint-
free and moistened cloth. Never use solvents or aggressive detergents. Disconnect the
device from power and allow it to cool before cleaning.
There are no serviceable parts inside. Do not open the housing. Do not try to repair the
device by yourself as this may result in damage.
PROTECTING THE ENVIRONMENT
When to be definitively put out of operation, take the product to a local recycling
plant for a disposal which is not harmful to the environment. Devices marked
with this symbol must not be disposed of as household waste. Contact your
retailer or local authorities for more information.
TECHNICAL SPECIFICATIONS
Power supply: .................230 V AC, 50 Hz / 2 W
Feed-through current: ......max. 16 A
DMX connectors:.............3-pin XLR (pin 1: ground, pin 2: signal -, pin 3: signal +)
Dimensions (W x D x H): ...141 x 110 x 41 mm
Weight: ...........................0.6 kg
Subject to change.
www.eurolite.de
Publ. 02/2018