Water-Saving Function; Setting The Scald Protection - Ernesto 78570/II Bedienungsanleitung

Use
3. Press the spray selector ON
side of the spray head
from the water jet to the spray jet. This function
is useful when washing vegetables and fruits as
they may be damaged by a normal water jet.
Press the spray selector OFF
side of the spray head
the normal water jet.
Hot water: swing the handle
Cold water: swing the handle
Check operation of the mixer. To do so, swing
the lever into all permissible positions.
1
Please check the connections regularly to
ensure that they are tight.
©

Water-saving function

The fitting has a water-saving function. This feature
limits the rate of water flow through the fitting. The
flow can be infinitely regulated between 0 – 100 %
by means of a stop.
Turn off the water supply.
Remove the red/blue hot/cold label
moving the lever
1
from the inside with a long flat object carefully
push the label out.
Release the lock screw
clockwise using the Allen key
CAUTION! Do not take the screw completely ot take the ot take the s
out; just loosen it until the lever n it unt un
taken off.
Take off the lever the lever the lever
1
Note: The setting screw e: The setting The settin
water flow is in the lever arm ater flow is in er flow
jects from th jects from the cartridge (Fig. G). ects from
To reduce the flow, turn the setting screw T T T T o red o reduc
clock clockwise. This limits the movement of the lever clo
arm a and therefore the lever
30
reduced as the lever
quite so high.
Note: The more you turn the screw clockwise,
the more the flow is reduced.
Place the lever
back on to the lever arm
1
and tighten the lock screw
8 GB/IE
on the under-
22 a
in order to change
22
on the under-
22 b
in order to return to
22
to the left.
1
to the right.
1
by by by
3
to the highest setting and t setting and etting and
object care ject care
by turnin by turnin by turning it anti-
2
Allen key en ke .
29 29
the lev the can be easily
1
.
for regulating the
31
, which pro-
30
31
. The flow is
1
now cannot be lifted
1
by turning it
2
clockwise using the Allen key
Press the red/blue hot/cold label
opening.
Turn on the water supply.
©

Setting the scald protection

(Fig. F)
The cartridge
7
tion function. This function is not activated before
leaving the factory (neutral setting).
CAUTION! Do not alter the setting of the scald
protection until you have installed the faucet.
Switch off the general water supply.
1. Remove the red / blue hot / cold plate
moving the handle handle
and pushing the plate out carefully from inside shing the pl hing the p
with a long, flat object. a l ong, flat ng, fla
2. Release the locking screw elease the ease th
key key key by t by turning it in an anticlockwise direction.
29 29
C CAUTION! You should not remove the screw C AU AUTIO T
comp co completely, but simply loosen it until the handle
can be easily removed.
1
3. 3. Remove the handle
4. Unscrew the cartridge end ring
the red adjusting ring
Note: Press the cartridge pins slightly back-
wards. This makes it easier to pull up the
adjusting ring
release the cartridge nut and do not take off
the cartridge
5. Reducing the hot water flow rate:
Replace the adjusting ring
ure F / 1 in offset position.
Restricting the hot water flow rate
completely: Install the adjusting ring
shown in Figure F / 2.
Deactivating the hot water flow rate
limitation: Install the adjusting ring
shown in Figure F / 3, neutral position.
6. After setting the scald protection device,
replace the cartridge cover ring
handle .
1
30
.
29
3
in this faucet has a scald protec- scald protec ald prote
tivated bef tivated befo
g). ).
e settin setti g of f
installed t installed th
general general
d d / / blue hot blue ho
andle into top-most position
1 1
with the Allen
2
.
1
. Now pull
4
upwards.
6
. Do not use pliers. Do not
6
.
7
as shown in Fig-
6
and the
4
into the
by
3
as
6
as
6