Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
½
Ensure that all seals are correctly seated.
½
DANGER OF SCALDING! When making
the hot water setting please ensure that the
temperature of the water is not too high.
½
Please note that seals are wear parts and
therefore will require to be replaced from time
to time.
½
BEWARE OF ELECTRIC SHOCK!
Leaks can put your life at risk from
electric shocks. Carefully check that
all connections are watertight. Also ensure that
all wires of electric appliances are correct and
have been securely installed.
½
Any leakage or sudden escape of water can
cause considerable damage to buildings and
property. All connections must therefore be
checked carefully to ensure that they are tight.
½
Familiarise yourself prior to installation with all
local conditions, e.g. water connections and
shut-off device.
©
Assembly
©
Installing the fitting
1. Shut off the main water supply. Al-
low the remaining water to run off.
2. Place the gasket
14
er side of the threaded ring
3. Using your hands, screw the two flexible hoses
into their designated holes
nated holes
nated hole
21
on the lower side of the tap (Fig. B).
ide of
e o
Both hoses are identical and suitable for warm
are identica
re identic
and cold water.
d water.
d water.
4. Screw the threaded pole
w the threade
the thread
which the gasket it into the middle hole on the
which the gask
ch the g
lower side of the tap. Push the flexible hoses
lower side o
ower side
and the threaded rod
and th
and the
in the sink.
in the
in t
5
5. Put the half-moon gasket
5.
Pu
metal disc
onto the threaded rod
16
6. Screw on the screw nut
er tap is attached to the sink unit. Please pay
attention to the pivoting range of the tap that
you require.
7. Screw the connector
pply. Al-
ply. Al-
r to run o
o run o
into the groove on the low-
e groove o
e groove on
.
.
13
13
rew the
w th
w
wo
and
10 a
10 b
he tap
he tap
with the side on
17
through the opening
17
and the half-moon
15
(Fig. C).
17
so that the, so mix-
18
onto the threaded rod
20
Safety advice / Assembly / Use
. Place the red fibre gasket
17
8. Screw the nylon sprinkler hose
connecting part
in between.
9. Attach the counterweight
hose
using the screws
25
10. The distance between the counterweight
and the sink unit should be approx. 40 cm.
11. Connect the flexible hoses
supply.
CAUTION:
Do not twist the hoses or place them under
tension.
Check all connections carefully after first-time
installation to make sure that they are tight.
In the event of incorrect installation, all waranty
t of incorrec
claims – particularly in relation to subsequent
– particular
particula
damage – are excluded.
ag
e – are e
– are
©
©
Flushi
Flushing the tap
Flus
In o
In ord
In order to remove any possible impurities, the tap
has to be flushed before it is used for the first time
h
ha
(Fig. E). Proceed as follows:
Note: Cover the parts that have to be screwed
with a damp cloth or with plastic clamps. This pre-
vents them from getting scratched.
1. Unscrew the mixing nozzle
2. Open the mains water supply and let the water
run for two minutes.
3. Screw the mixing nozzle
rinser
.
22
©
Use
21
©
Bringing into use
Note: If the tap has not been used for a long period
flush the pipes through thoroughly in order to avoid
stagnation and build-up of residues.
1. Open the main water supply.
2. Lift the handle
left in order to regulate the speed or tempera-
ture of the water.
in between.
19
onto the
25
(Fig. D). Place the seal
20
to the mixer
27
.
28
to the water
21
r place
plac
them
th m
tions carefu
ons caref
make sure
make sure t
f incorre
.
23
back onto the
23
and swing it to the right or
1
26
27
m.
m.
water
water
GB/IE
7
Werbung
Kapitel
Inhaltsverzeichnis
