Operation - Bosch GIC 120 Professional Betriebsanleitung

OBJ_BUCH-2377-001.book Page 10 Thursday, February 26, 2015 9:55 AM
10 | English
13 Latch of battery lid
14 Camera connection
15 Camera cable lock
16 Magnet
17 Hook
18 Mirror
Display Elements
a Status bar
b Selected magnification
c Selected lighting/brightness
d Battery indicator
e Compass View with reference point (Up Indicator)
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Digital Inspection Camera
Article number
Rated voltage
Operating temperature
Storage temperature (hand unit
without batteries)
Relative humidity
Smallest bending radius of camera
cable
Diameter of camera head
Display resolution
Operating time, approx.
Weight according to
EPTA-Procedure 01/2003
Dimensions (length x width x
height)
1) Free of moisture condensation
2) At 50% brightness of the illumination light in the camera head
Assembly
Inserting/Replacing the Batteries
It is recommended that you use alkali-manganese batteries to
operate the inspection camera.
To open the battery lid 12, press the latch 13 and fold open
the battery lid 12. Pull out the battery compartment 11 and
insert the batteries. When inserting, pay attention to the cor-
rect polarity according to the representation on the inside of
the battery compartment 11. Slide the battery compartment
11 all the way in and close the battery lid 12.
The symbol will initially appear on the display if the charg-
ing condition of the batteries is low. When the battery symbol
is empty, you have to replace the batteries because inspec-
tions are no longer possible.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
1 609 92A 122 | (26.2.15)
 Remove the batteries from the inspection camera
when not using it for a prolonged period of time. The
batteries can corrode and self-discharge during prolonged
storage.
Mounting the Camera Cable (see figure A)
For operation of the inspection camera, the camera cable 7
must be mounted to the hand unit 1.
Attach the plug of the camera cable 7 to the camera connec-
tion 14 in the correct position until it engages.
Dismounting the Camera Cable (see figure B)
To remove the camera cable 7, press the lock 15 together and
pull the plug out of the hand unit 1.
Mounting the Mirror, Magnet or Hook
(see figure C)
The mirror 18, the magnet 16 and the hook 17 can be mount-
ed to the camera head 8 as auxiliary aids.
GIC 120
Slide one of the three auxiliary aids to the stop onto the recess
3 601 B41 1..
on the camera head 8 as shown in the figure.
V= 6.0
Note: The magnet 16 and the hook 17 are only suitable for
moving and removing loose, small and light objects. Applying
°C –10...+50
too much tension can damage the inspection camera or the
auxiliary aid.
°C –20...+60
1)
% 5–95

Operation

 Keep the hand unit 1 and the batteries dry and protect
mm 25
them from direct sunlight. The camera cable and camera
mm 8.5
head are waterproof when mounted correctly. However,
320 x 240
the hand unit and the batteries are not protected against
2)
h 5.0
water. If they come into contact with water, there is a risk
of electric shock or damage.
kg 0.5
 Do not subject the inspection camera to extreme tem-
peratures or variations in temperature. As an example,
mm 197 x 85 x 49
do not leave it in vehicles for longer periods. In case of
large variations in temperature, allow the inspection cam-
era to adjust to the ambient temperature before putting it
into operation.
 Do not use the inspection camera when the lens on the
camera head 8 is misty or fogged-up. Do not switch the
inspection camera on until after the moisture has evap-
orated. Otherwise, the inspection camera can become
damaged.
 The switched-on illumination light 9 can become hot
during operation. In order to prevent burns, do not touch
the illumination light.
Initial Operation
Switching On and Off
To switch on the inspection camera, press the On/Off button
2. The start screen will be shown on the display 5 for a short
time.
Note: If the camera cable is not mounted when the tool is
switched on, the display will show an error message.
Bosch Power Tools