Power Dynamics 172.710 Gebrauchsanweisung Seite 7

AUTO CUE
Push the SGL/CTN button for more than 1 second to switch between normal and "auto cue" mode. This function will automatically set
a cue point to the first music note of each track.. If a new track is selected, a new CUE POLNT will be set to reflect the new starting point.
SETTING A CUE POINT
A cue point is the exact point playback will begin when the PLAY/PAUSE BUTTON is pressed. A cue point may be created anywhere on a
music source device or in a track.You may press the IN BUTTON while the music is playing. This will set a CUE Point without music
interruption.
Pressing the CUE BUTTON will now return you to thesame point that you pressed the IN BUTTON. Pressing the CUE BUTTON will
now return you to this exact point.
(2)You may also use the jog Wheel to set a cue point. While music is PAUSE or CUE mode and JOG WHEEL is in PITCH mode,
use the jog wheel to scroll through a track and find your desired starting point. Once you have found your desired CUE point press
the play Button to set your cue point. Pressing the cue Button will now return you to this exact point.
SEAMLLESS LOOP
1. CREATING AND PLAYING A SEAMLESS LOOP
A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to create dramatic effect in
your mixing. This loop has no time limit and you could actually loop the entire length of the current folder. You can create a seamless
loop between two continuous points as below.
(1) Press PLAY/PAUSE BUTTON to activate playback mode.
(2) Press the IN BUTTON. This will set the starting point of the SEAMLESS LOOP. The IN BUTTON LED will glow
(3) Press the OUT BUTTON to set the ending point for your SEAMLESS LOOP. The IN BUTTON and OUT BUTTON LEDs will
immediately begin to flash rapidly, indicating the SEAMLESS LOOP mode has been activated.
2. EXITING A LOOP
To exit a SEAMLESS LOOP, press the OUT BUTTON. The IN BUTTON and OUT BUTTON LEDs will remain on, but will stop
flashing. Music playback will resume normal play. The IN BUTTON, OUT BUTTON LEDs and RELOOP/LOOP indicator in the
LCD will remain on to remind you that a loop is stored in memory.
3. REPLAY LOOP
The RELOOP function allows you to return to your stored loop at any time. The IN BUTTON and OUT BUTTON LEDs will indicate
a loop is stored in memory, and may be played at any time. To replay the loop, press the RELOOP BUTTON. The IN BUTTON and
OUT BUTTON LEDs will again begin to flash indicating SEAMLESS LOOP mode has been activated and your stored loop will
immediately begin to play.
- When you use the Track Encoder to change songs, the previous CUE and LOOP memories will be erased, new CUE is set at the
beginning of the selected song.
- When you wait for the current song (song A) to finish, and play the next song (song B), the previous CUE and LOOP memories (of
Song A) are still kept, and when you press the CUE or RELOOP, it can go back to the CUE or LOOP of Song A. But, when play to
the next folder, the previous CUE and LOOP memories will be erased too.
4. EDITING A LOOP
You can edit your seamless loop, but you must first have created a seamless loop to edit. If you haven't created a SEAMLESS
LOOP, follow the instructions in step 1 to create a loop.
There are three methods as below:
(1) Edit a seamless loop's ending point
You can edit the end point of the loop to make your loop shorter or longer. Make sure the loop that you want to edit is not in RELOOP
mode. Pause in PITCH mode; turn the JOG WHEEL to make the loop shorter /longer. Press the OUT button to set the new ending point
of your loop and then press the RELOOP button to make the loop active.
(2) Edit a seamless loop's starting point
You can edit the staring point of the loop to make your loop shorter without interrupting. Under the RELOOP mode, turn the JOG
WHEEL clockwise in PITCH mode to make the loop shorter. Please make sure the new starting point must before the ending point.
Press the IN button to set the new starting point of your loop.
(3) Reset a loop
You can reset a new loop under the play or pause mode, Whenever you find a more desired starting point press the IN button, the LED
of OUT button will go out, Find a new ending point and press the OUT button to set the ending point of your new loop.