Herunterladen Diese Seite drucken

Werbung

SUPPLIED MATERIAL
Lamp structure / Estructura l u minaria / Leuchten-Struktur
1
TECHNICAL SPECIFICATIONS
Net Weight / Peso Neto / Netto-Gewicht 7,75 Kg
4510.
Caution / Precaución / Vorsicht
EN
Before assembling and installing this product, carefully
read the following:
-Switch of the mains before installing the lamp.
-If you wish to fix the lamp to the ground, choose the most
adequate plugs and screws depending on the surface.
-Before the installation, make sure the installation surface will
not be damaged. If this happens, it will be the installator´s
responsibility.
-If the steel cable or the power cord of this lamp is damaged, it
must be replaced only by the manufacturer or their technical
service or by a person capacitated to this effect to avoid any
risk.
-We recommend reading the manual before installaing the
lamp. Keep this instructions for future reference.
Palo Alto
Design by Xuclà
ASSEMBLY INSTRUCTIONS
INSTRUCCIONES DE MONTAJE
MONTAGEANELITUNG
MATERIAL SUMINISTRADO
ESPECIFICACIONES TÉCNICAS
2 x LED 3W 700mA
ES
Antes de proceder al montaje e instalación de esta
luminaria, leer detenidamente las siguientes
consideraciones.
-Desconectar el suministro eléctrico antes de proceder a la
instalación de la luminaria.
-Si se desea fijar la luminaria al suelo elegir los elementos de
fijación mas adecuados en función del soporte de instalación.
-Asegurarse antes de realizar esta operación que no se
producirán daños irreparables en el soporte de instalación. En
caso contrario la responsabilidad será del instalador.
-Si el cable flexible o cordón de esta luminaria está dañado,
deberá sustituirse exclusivamente por el fabricante o su
servicio técnico, o por una persona con cualificación
equivalente con objeto de evitar cualquier riesgo
-Recomendamos leer el manual antes de iniciar la instalación
de la luminaria. Guardar estas instrucciones para futuras
consultas.
GELIEFERTES MATERIAL
4510
1 un.
TECHNISCHE DATEN
Class I. Product with an additional protection cable (grounds).
50 Hz
Clase I. Aparato con un cable protector adicional (toma de tierra).
Klasse I. Apparat mit zusätzlichen Schutzleiter (Erdkabel).
Dust-tight product. Protected against water trickles.
Producto totalmente estanco al polvo. Protegido contra los chorros
de agua.
Staubdicht. Schutz gegen das Eindringen von Strahlwasser.
Product that CAN be in contact with normally-flammable materials
(wood or others).
Está permitido que producto con este distintivo esté en contacto
con materiales normalmente inflamables (maderas u otros).
Es ist erlaubt Produkte mit diesem Etikett auf normal entflammbaren
Oberflächen (Holz usw.) zu montieren.
Alternating current
Corriente alterna
Wechselstrom
D
Bevor Sie mit der Montage dieser Leuchte beginnen,
sollten Sie die folgenden Hinweise in aller Ruhe lesen und
berücksichtigen.
- Schalten Sie vor dem elektrischen Anschluss den Strom ab.
-Sollten Sie die Leuchte fix auf dem Boden befestigen wollen,
wählen Sie für die vorgesehene Vorrichtung das dafür
geeigneste Begestigungsmaterial.
-Vergewissern Sie sich vor diesem Prozess, dass die
Vorrichtung hierduch nicht dauerhaft beschädigt wird. Im
entgegengesetzten Falle wäre der Installateur hierfür
verantwortlich.
- Wenn das Kabel dieser Leuchte beschädigt werden sollte,
muss es ausgetauscht werden. Dies darf ausschliesslich nur
durch den Fabrikanten, seinem Kundendienst oder einer
hierfür qualifizierten Person geschehen, um jegliche Gefahr
ausschliessen zu können.
-Wir empfehlen vor Montagebeginn die Anleitung zu lesen.
Bewahren Sie die Anleitung für etwaige zukünftige Fragen auf.
1.

Werbung

loading

Inhaltszusammenfassung für VIBIA Palo Alto

  • Seite 1 Palo Alto Design by Xuclà ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANELITUNG SUPPLIED MATERIAL MATERIAL SUMINISTRADO GELIEFERTES MATERIAL 4510 1 un. Lamp structure / Estructura l u minaria / Leuchten-Struktur TECHNICAL SPECIFICATIONS ESPECIFICACIONES TÉCNICAS TECHNISCHE DATEN Class I. Product with an additional protection cable (grounds).
  • Seite 2 ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG IMPORTANT NOTICE: Switch off the mains before installing the lamp. 1. Remove the screws (A) to free the plates (B). 2. Remove the cover (C) by taking out the two screws (D). 3. Unhook the connection cylinder (E) from the tabs securing it.
  • Seite 3 Verbindung bei dem Sie die Leuchte bezogen haben. GRUPO T DIFFUSION S.A. Barcelona, 72-74. 08820 El Prat de Llobregat (Barcelona - Spain) Nacional Tel 934 796 970. Fax 934 796 973. Internacional Tel +34 934 796 971. Fax +34 934 782 026 www.vibia.com grupo-t@grupo-t.com...