Compiling An Individual Title Sequence - IMG STAGE LINE DPR-10 Bedienungsanleitung

5.10 Compiling an individual
GB
title sequence
For playing only a selection of titles in a certain
order, a sequence of 64 titles as a maximum can
be programmed. For programming, the numbering
of the folders should be known because the corre-
sponding number of the folder has to be entered for
each title to be programmed (
1) The player must be set to stop (indication STOP),
press the button
2) Switch on the programming mode with the but-
ton PROG (20) on the remote control. The dis-
play shows "000 P-01" and the indication PRO-
GRAM is shown in the upper line.
3) First select the number of the folder containing
the first desired title for the title sequence. This
is also required if all titles are in the ROOT di-
rectory without folder. The root directory has
the number 1.
Select the folder number with the buttons
[REV*] and
keys (14). To memorize, press the button
PROG. The three zeroes in front of the indica-
tion "P-01" flash as a request to enter the title
number.
4) Select the number of the first title for the title se-
quence with the buttons
[CUE] or enter it with the numerical keys. For ti-
tles in folders please observe that not all titles
are consecutively numbered on the storage
medium now but that the first title in a folder has
the number 1 in each case.
5) To memorize, press the button PROG. The dis-
play goes to the next memory location number
"P-02".
6) Repeat the operating steps 3 to 5 for all further
desired titles until the complete title sequence
will be programmed.
7) To start the title sequence, press the button
(7) [PLAY/ PAUSE*].
8) With the buttons
title of the title sequence can be selected or, by
keeping the respective button pressed, the fast
forward/reverse within a title can be activated.
9) After playing the title sequence or with pressing
the button
and the indication PROGRAM will be extin-
guished. For starting the title sequence again,
first press the button PROG and then the button
[PLAY/ PAUSE].
Note: A programmed title sequence is deleted when
switching to another storage medium, when pressing
*Lettering on the remote control
14
chapter 5.4.4).
[STOP*] (6), if required.
[CUE*] (8) or with the numerical
[REV] and
[REV] and [CUE] each
[STOP] the player is set to stop
the button [STOP] in the programming mode, and
when switching the unit off.
5.11 Audio recordings
1) The write protection of the storage medium
must not be activated, deactivate the protec-
tion, if required.
2) For recording on an SD / MMC card, no USB
stick must be inserted. With SD / MMC card and
USB stick inserted, the recording is always
made on the USB stick.
3) Press the button FUNC (5) so many times until
AUX is displayed. Thus, a unit connected to the
jacks AUX INPUT (17) is selected as a signal
source for the recording.
4) For the recording three different data rates can
be adjusted. The following data rates are avail-
able:
REC HIGH = 192 kbit / s
REC LOW = 96 kbit / s
REC MID = 128 kbit / s
After switching on the DPR-10, always REC
MID is adjusted.
To adjust another data rate, keep the button
REC (4) pressed: the next data rate is selected
and displayed. Either keep the indicated data
rate or select the next one by shortly pressing
the button REC. After a few seconds the display
goes back to the indication AUX and the last
data rate indicated is adjusted.
5) To start the recording, press the button REC.
The unit prepares the recording and REC WAIT
flashes in the display for approx. 3 seconds. As
soon as the recording starts,
played.
However, if the display changes to REC
USB, an SD / MMC card and a USB stick have
been inserted. The recording can now only be
made on the USB stick (see operating step 2)
and only starts when pressing the button REC
again.
Note: If the indication REC NG is displayed, the
recording was not started or was stopped. Possible
cause: The write protection is still activated, the stor-
age medium is full, an operating error has been
made.
6) While recording, all buttons are locked, except
REC and [STOP*] (6). They serve to stop the
recording. After terminating the recording, the
indication REC OK is shortly displayed. Then
the display is switched back to the indication
AUX.
r EC AUX is dis-