Bosch PSR 14,4 LI Originalbetriebsanleitung Seite 19

Note: The battery is supplied partially charged.
To ensure full capacity of the battery, completely
charge the battery in the battery charger before
using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the
battery.
The Li-ion battery is protected against deep dis-
charging by the "Electronic Cell Protection
(ECP)". When the battery is empty, the machine
is switched off by means of a protective circuit:
The inserted tool no longer rotates.
Do not continue to press the
WARNING
On/Off switch after the ma-
chine has been automatically switched off. The
battery can be damaged.
To remove the battery 6, press the battery un-
locking button 11 and pull the battery out of the
power tool toward the rear. Do not exert any
force.
For charging, the battery 6 can also remain in the
power tool. During the charging procedure, the
power tool cannot be switched on. Press the
On/Off switch 10 to check the charge condition
of the battery, see Section "Battery Charge-con-
trol Indication".
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A long
battery service life is achieved in this manner.
Observe the notes for disposal.
Changing the Tool (see figure B)
Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
The drill spindle is locked when the On/Off
switch 10 is not pressed. This makes quick, con-
venient and easy changing of the tool in the drill
chuck possible.
Open the keyless chuck 2 by turning in rotation
direction , until the tool can be inserted. Insert
the tool.
Bosch Power Tools
Firmly tighten the collar of the keyless chuck 2 by
hand in rotation direction
tion ("click") is heard. This automatically locks
the chuck.
The locking is released again to remove the tool
when the collar is turned in the opposite direc-
tion.
Replacing the Drill Chuck
(see figures C–E)
Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
The keyless chuck 2 is secured with a securing
screw 13 against unintentional loosening from
the drill spindle. Completely open the keyless
chuck 2 and unscrew the securing screw 13 in ro-
tation direction . Please note that the securing
screw has a left-hand thread.
If the securing screw 13 is seated tightly, apply a
screwdriver to the screw head and loosen the se-
curing screw by giving a blow onto the handle of
the screwdriver.
Removing the Drill Chuck (see figure D)
Clamp the short end of an Allen key 14 into the
keyless chuck 2.
Place the machine on a stable surface (e.g. a
workbench). Hold the machine firmly and loosen
the keyless chuck 2 by turning the Allen key 14 in
rotation direction
less chuck by giving the long end of the Allen key
14 a light blow. Remove the Allen key from the
keyless chuck and completely unscrew the key-
less chuck.
Mounting the Drill Chuck (see figure E)
The keyless chuck is mounted in reverse order.
Note: After mounting the keyless chuck, screw
the securing screw 13 in again.
The drill chuck must be tightened with a
tightening torque of approx. 17–23 Nm.
English | 19
until the locking ac-
. Loosen a tight-seated key-
2 609 002 498 | (7.1.08)