Bosch PTK 14 E Originalbetriebsanleitung Seite 11

Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Trigger
2 Thumbwheel for hammer-force preselection
3 Magazine slider
4 Latching aperture for support foot
5 Latching aperture for spacer clamp
6 Latching aperture for stapler plate
7 Tacker head
8 Selector switch for DuoTac-Automatic
9 Nail strip*
10 Staple strip*
11 Magazine
12 Support foot*
13 Stapler plate*
14 Spacer clamp*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-16.
Typically the A-weighted noise levels of the product are:
Sound pressure level 87 dB(A); Sound power level 98 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a and uncertainty K determined ac-
h
cording to EN 60745:
2 2
a = 6.6 m/s , K= 1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
.
Technical Data
Tacker
Article number
Impact rate
Intermittent operation
Staple width
Staple length
Nails
Magazine capacity, max.
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-16.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, Germany
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, Germany
Leinfelden, 07.05.2014
Assembly
Loading the Magazine (see figure A)
 Before any work on the machine itself, pull the mains
plug.
 Use only original Bosch accessories. The precision com-
ponents of the tacker, such as magazine, striker and im-
pact channel, are adapted for Bosch staples, nails or pins.
Other manufacturers use different steel qualities and
measures.
– (1) Press on both sides of the magazine slider 3 and pull
out the magazine 11.
– (2) Insert the staple strip 10 or the nail strip 9. Hold the
tacker at a slight angle when inserting the nail strip 9, so
that the nails face against the sidewall.
– (3) Slide in the magazine 11 until the closure on the mag-
azine slider 3 engages.
English | 11
PTK 14 E
0 603 265 2..
-1
min
min
mm 11.4
mm 6– 14
mm
kg
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 0PL | (7.5.14)
30
15
14
100
1.1
/II