Electrical Connection; Mechanical Installation - dot-spot brilliance 230V Bedienungsanleitung

Configurations

Electrical connection

Order number
5 m H07 RN-F rubber cable,
.52
with IP 44 Schuko plug
Optional accessories
Metal mounting sleeve with
94300
mounting screws, ds EH
marten repellent MS 93001
Safety
Intended use
The recessed spot brilliance 230 V is intended for fixed floor, wall and ceiling installation. It is suit-
able for effect lighting of plants, objects and architecture. It is designed for operating in moderate
climatic zones. The "ds" versions in combination with the metal mounting sleeve meet the require-
ments of EN 60598-2-13 "Special requirements - floor-mounted luminaires" for all areas, also in
accordance with section 13.6.2 for use in areas of roadways, parking lots etc. The spot is meant for
operating with for operation with mains voltage 230 - 240 V, 50 - 60 Hz. In case of detailed lighting
planning, please request the light distribution curves (LDC). The adjustment mechanism for the
light angle of the brilliance 230 V is laid out for setting up during installation.
Installation to be carried by an expert
The installation must only be carried out by appropriately trained professionals. If the electrical
connection is a fixed connection, without a Schuko plug, the connection must only be carried out
by a qualified electrician.
Safety instructions
During installation, the relative safety regulations have to be followed. The spot is operated
with mains voltage 230 - 240 V. To avoid danger and failures, prior of any work at the spot
or installation, disconnect the spot from the mains. Connect the spot only to sockets with a
voltage of 230 - 240 V AC, 50 - 60 Hz. A wrong voltage may destroy the spot.
In case of damage to the spot or the connection cable, it must not be operated any further and
must be disconnected immediately from the mains. In case of contact with 230 - 240 V mains
voltage it can lead to serious injuries or even death!
In order to protect the exposed connection cable from rodents it should be protected against mar-
tens (see installation accessories).
High ambient temperatures shorten the life of the LED's. Ensure a good heat dissipation in order to
guarantee a long life of the LED. During operation, do not expose the spot to ambient temperatures
of > 45°C. Do not cover the spot, provide free air circulation.
18
Comment
Termination possible by cutting
the Schuko plug
only for "ds" version
length 50 cm
Safety
Safety instructions
Do not open the housing of the luminaire other then mentioned to adjust viewing angle. The tight-
ness of the brilliance is only guaranteed if also the outer sheath of the connection cable is undam-
aged and if the connection cable is bonded in a waterproof way. Otherwise, because of the capillary
effect, the penetrating moisture can reach and destroy the electronics of the spot.
Assembly
Preparation
Depending on the configuration, unpack all the parts included in the scope of delivery and check
them for completeness and intactness. Dispose of the packaging material no longer needed in
accordance with applicable regulations.
If you notice any damage from transport, immediately contact the dealer where you purchased the
luminaire.

Mechanical installation

The recessed spot brilliance 230 V can be incorporated into solid materials such as wood or stone
directly without mounting sleeve. When mounting in loose materials or concrete using the mounting
sleeve is recommended.
The "ds" variants can be fastened directly in fixed materials such as wood or stone with corre-
sponding countersunk head screws. Optionally the metal housing sleeve "ds EH", Art.-No.: 94300,
available as a special accessory can be used.
In order to prevent a permanent flooding of the luminaire, it may be necessary to provide a drain
below the spot.
Preparing direct installation of the spot into the substrate
brilliance 230 V, not "ds" version
The installation of the brilliance 230 V can be done directly in all suitable materials that have the
required strength for holding the recessed spot, e.g. wood, concrete and natural stone. The spot is
held by the lateral stainless steel springs inside the hole. Observe the position of the spot and the
resulting stress on the material. The supplied mounting sleeve can (eg. in case of sheet materials)
be below installed and thus used as a mounting room.
Drill the installation hole for the spot. The required borehole diameter is between 75 and 78 mm. In
case the spot is supposed to be installed in solid material, e.g. massive concrete wall, stone, scree
floor, the hole must be at least 75 mm deep plus the space for the respective cabling. A deeper hole
facilitates the accommodation of the excess supply cable when inserting the spot.
Prepare the connection.
In case the spot is exposed to loads, the surface on which the bezel of the spot rests must be level
and capable of bearing the load.
19