Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1. Introduction
This pellet-burning chimney stove is a first-class
product of modern heating technology.
Extremely easy to operate, modern regulation tech-
nology and efficient combustion technology enable its
use as a high-quality room heater, without having to
sacrifice the pleasant atmosphere of a fire place.
Proper installation as well as correct handling and
care are vital to trouble-free operation and a long life.
Please read all the information contained in these
instructions carefully. They contain important infor-
mation regarding safety, installation, usage and
maintenance of the unit.
These instruction must
•
be given to the operator after installation. In addi-
tion, the operator must be personally instructed in
the operating procedure of this unit.
•
carefully stored and handed over to all subse-
quent owners.
•
be provided to the technician for maintenance
procedures
The manufacturer is not liable if the following instruc-
tions are not observed. The units may not be improp-
erly used for any unintended purposes.
Carefully preserve this operating manual, so that you
can easily remind yourself of proper operation at the
start of a new heating seasion. Should you determine
any damage due to transport, please inform your
distributor at once. Otherwise no adjustment claim
that is free of charge will be possible.
This heater is not intended for operating by persons
(including children), with reduced physical, sensory
or mental abilities or for lack of experience and/or for
lack of knowledge to be used it by a person respon-
sible for their security is supervised or received from
instructions like the heater to use. Children should be
supervised, in order to guarantee that they do not
play with the heater.
Technical information
2.
- Nominal heat output
- Connection fitting for stove pipe
- Connection fitting for combustion air
- Weight
- Pellet container capacity
- Pellet consumption heat output
- Type of operation
3. Guidelines
•
Local building regulations
•
The chimney stove must be installed and con-
nected to the chimney by a qualified professional.
The DIN and EN norms and country-specific reg-
ulations must be observed for the safe installa-
tion of the unit.
[kW]
8.9
∅ 80
[mm]
∅ 80
[mm]
[kg]
136
[kg]
~18
[kg/h]
~2,2
Continuous combustion
•
The chimney stove corresponds to DIN EN
14785 and 15a BV-G (Austrian Civil Code).
Adequate supply of combustion air must be ensured.
Please contact your local master chimney sweep,
distributor or professional technician.
4. Chimney calculation
The chimney calculation is based on DIN EN 13384-
2 and/or the country-specific regulations.
Required information
•
Nominal heat capacity
•
Exhaust flow
•
Exhaust temperature
•
Required feed pressure
at exhaust connector fittingsIn the case of excessive
feed pressure >20 Pa, a feed pressure limit (for ex-
ample, auxiliary air device in the chimney) must be
implemented.
For the chimney calculation, the required feed pres-
sure must be set at 0 Pa at the exhaust connector
fittings.
Multi-flue chimneys are possible with a special per-
mit. Please contact your master chimney sweep.
5. Combustion air supply
Adequate supply of combustion air must be ensured.
The combustion air is either drawn from the installa-
tion room, or from a combustion air line that is con-
nected directly to the unit and leads from the cellar or
outdoors.
We recommend Olsberg stove pipes D=80 mm with
sealing lip.
Important:
Combustion air intake and convection air open-
•
ings may not be closed or covered during heating
operation. Should there be a ventilation unit or
extractor hood in operation in the ambient air
network, risk-free operation of the chimney stove
must be ensured by the implementation of safety
equipment.
•
In the case of simultaneous operation, the result-
ing negative pressure in the installation room
may not exceed 4 Pa.
6. Installing the chimney stove
The installation base must be flat and level. The
chimney stove may only be installed on an adequate-
ly sturdy base. In order to protect the floor covering,
the chimney stove may be placed on a metal floor
sheet or glass plate.
A stable and heat resistant base must be used on
combustible flooring or carpet. This must extend be-
yong the combustion chamber of the chimney stove
by 50 cm towards the front and 30 cm on each side.
- 19 -
[kW]
8.9
[g/s]
5.5
[°C]
200
[Pa]
0
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
