Dell Wyse 5020 Kurzanleitung Seite 3

Initial Environment Setup
The Dell Wyse P25 zero client is for use with PC-over-IP (PCoIP) protocol
environments. The zero client connects to a host server which is PCoIP
capable.
Before setting up and using the zero client, you must have a properly installed
PCoIP environment that it can access. This guide will help you to set up the
zero client and establish a remote connection to your host server using PCoIP
technology, enabling you to use applications and desktop peripherals as if
you were using them locally.
NOTE: PCoIP technology is designed to deliver a user desktop from a
centralized host server across standard IP networks – including full DVI dual
monitor video, complete USB 2.0 compatibility, and full-duplex
high-definition audio.
Setting Up Your Zero Client
Be sure you have read all safety guidelines before setting up and operating
this product. Refer to the figures and proceed as follows:
1
Make sure the monitor and the zero client are turned off and
disconnected from AC power. Place the zero client on a desk or use
the horizontal stand/bracket for VESA mounting (assemble with the
920275-03L screw kit; insert the thin client with cables facing down or
to the side, but never facing up).
2
Make all desired connections. The monitor, keyboard with mouse, and
Ethernet network are required. Additional connections of peripheral
devices may be made at this time.
3
Connect the power adapter to the zero client power input before
connecting to a 100-240V AC, 50-60 Hz electrical outlet.
4
Press zero client Multifunction power button to apply power. The
power button will light blue; wait for the monitor to display the On
Screen Display (OSD).
LED indicators* include:
Status LED Bi-color light for connected / not connected
(green/amber)
Power LED Single light for power on/off (blue)
* For detailed LED indicators information, go to the Dell Wyse Knowledge
Base at www.dell.com/wyse/knowledgebase and search for
solution 22671.
NOTE:
If the monitor does not show the OSD, check all connectors and make
sure the monitor and zero client are turned on.
NOTE:
For more information refer to the user and administrators guides, or
contact your Dell support.
Additional Notes
Monitor Types: In addition to DVI and DisplayPort monitors, the zero client is
compatible with analog VGA and digital HDMI monitors. See www.dell.com
for information about approved adapters for connecting VGA and HDMI
monitors to the zero client.
Note: Audio for HDMI is not supported.
IP Address: The zero client is set to DHCP client mode by default. Normally,
the IP address of the zero client and host server are assigned by the DHCP
server on your IP network. If your IP network does not have a DHCP server,
the zero client and host server will fall back to a static IP address mode after a
time-out period of approximately 2 minutes. In the fall back static IP address
mode, you can access the zero client to disable DHCP client mode and assign
a static IP address. The zero client fall back IP address is 192.168.1.101.
Multifunction Power Button/LED:
•
Press the button and light turns on: Turns on the zero client.
•
Press and hold the button until light turns off: Turns off the zero client.
•
Press the button when zero client is connected in a session:
Disconnects zero client from the host server.
Configure
The zero client can be configured to use DHCP or Static IP addressing. To
change the settings, in the On Screen Display go to Options > Configuration
> Network tab. You may need to unlock the settings page with a password
(default password is Administrator).
Establishing a PCoIP Connection
1
Turn on the zero client and click Connect.
2
Enter the IP address of your connection broker if not configured by
your IT administrator.
NOTE:
If the Connect button on the zero client user screen is inactive (grayed
out=inactive) or if the zero client cannot discover host servers on the
network, check the network connection and make sure the Ethernet switch or
router is turned on.
3
Enter your user name and password (both are case sensitive). Once
authenticated, a list of hosts you are authorized to connect to will
appear.
4
Select the host to which you want to connect and click OK.
After a successful PCoIP connection, the Status LED of the zero client
will light green. You are now connected.
NOTE: For more details, see About the OSD in the Administrators Guide:
PCoIP Release 4.0.x.
Safety Guidelines
Improper connection, mounting, or use of this product could result in
component failure or undesired interference. Read the following guidelines
before setting up and operating your device.
Setup
•
Do not connect to AC power until all other connections (including the
power adapter) are made. Connecting or disconnecting components
or equipment on the back panel when the device is receiving AC
power can cause power surges and damage the device.
•
Do not force a connector into its socket. If any undue resistance is
encountered, ensure that the connector is correctly oriented to the
receptacle.
Venting and Care
•
Mount the device only as shown or in accordance with the instructions
provided with Dell Wyse-approved mounting accessory kits. Improper
orientation could restrict the airflow of heat from the device and
damage it.
•
Allow sufficient space around the device for ventilation; do not place
the device in any enclosure that restricts airflow around the device; do
not place any objects on the device or block the vent outlets. For
environmental operating specifications, locate your product and
download the Fact Sheet using the Cloud clients tab at:
www.dell.com/wyse/P25
Power Sources
•
For regulatory compliance use only the power adapter that comes
with your device or a Dell Wyse-approved equivalent. For proper
replacement compare the labels on both device and power adapter to
ensure that their voltages match.
WARNING:
Use of any other power adapter may damage your
device or the power adapter. The damage caused by an improper
power adapter is not covered by warranty.
•
When turning off the device, make sure to perform a complete
shutdown (via the power button). Do not disconnect the AC power
cord, DC power cord, or shut off power at a circuit breaker (including
power strips), etc., to turn off the device.
•
Surge protectors for electrical devices are recommended in areas of
lightning. However, when lightning is occurring, your equipment
should be properly shut down and unplugged from AC power until the
storm has passed.
Need more information?
Dell Reference Guides - Documentation is available at:
www.dell.com/wyse/manuals
Dell Approved Mounting Accessory Kits - Information about approved
mounting accessory kit options is available at:
www.dell.com/wyse/accessories
Dell Support - Upgrade software images for installation are available at:
www.dell.com/wyse/downloads
Dell Device Manager - Information about Wyse remote management
software is available at: www.dell.com/wyse/WDM
DEll and the Environment - Information about Dell compliance with RoHS
and with the Waste Electrical and Electronic Equipment (WEEE) is available at:
www.dell.com/environment
Dell and Recycling - Information about recycling unwanted Dell product
within the United States is available at: www.dell.com/recycling
Dell Warranty - The standard warranty is three years from the date of
purchase.
__________________________________________________________________
Copyright © 2014 Dell Inc. All rights reserved.
This product is protected by U.S. and international copyright and intellectual
property laws. Dell and the Dell logo are trademarks of Dell Inc. in the United
States and/or other jurisdictions. All other marks and names mentioned
herein may be trademarks of their respective companies.
Sept 2014 Dell PN: JW46G Rev: A00