Controls - Fohnn Direct-Studio Bedienungsanleitung

4.3 Controls

All controls, inputs, and outputs of the Direct-Media / Direct-
Studio are located on the loudspeaker enclosure rear panel.
Refer page 12.
A sturdy carrying handle is integrated in the Direct-Media.
(1) Main input
Main input jack for operating the Direct-Media / Direct-
Studio on 230 VAC power using the supplied cable.
(2) Power fuse
The power fuse is located below the power input socket.
Prior to replacing the power fuse unplug the Direct-Media /
Direct-Studio from power. Make sure to use replacement
fuse of the same type as the original fuse only:
1,25AT (5x20mm) for 230 VAC
(3) POWER switch (on/off)
Switches power to the Direct-Media / Direct-Studio audio
section and amplifier on and off. The STATUS LED in the
POWER switch (3) will illuminate red when power on.
(4) signal LED
Turn on the power switch (3) the power indecator signal
LED (4) will light.
(5) Peak LED
The overload indicator flashes when the loudspeaker´s on-
board amplifier are driven to their maximum signal output.
Occasional flashes are normal for very loud operation.
However, if the overload indicator stays lit, please reduce
the power, bacause the sound may be distored.
(6) LINE INPUT L/R
These two RCA jacks allow you to connect a CD player,
cassette recorder, or other line level source to your Direct-
Media / Direct-Studio using a stereo RCA cable (not
supplied). The stereo input signal is internally summed to
mono.
Input sensitivity is 100 mV into 10 kΩ for nominal level.
(7) LINE INPUT
This jack 6,3mm allows you to connect a CD player,
cassette recorder, or other line level like keyborads and
mixer sources to your Direct-Media / Direct-Studio using a
mono cable (not supplied).
Input sensitivity is 100 mV into 10 kΩ for nominal level.
(8) VOLUME
This rotary potentiometer sets the loudness volume of the
audio source connected to the LINE INPUT jacks (6) and
(7).
Option wireless microphone in Direct-Media: This rotary
potentiometer sets the loudness volume of the wireless
microphone.
(9) mix/rec Output
This jack allows you to connect either a recorder or another
Direct-Media / Direct-Studio to your unit using a standard
cable (not supplied).
This jack carrys the output signal of the biult-in mixer with
all the volume and EQ settings you made. The output
voltage at nominal level is 1 V into 200 Ω source
impedance.
(16) Mic input (only Direct-Media)
This balanced female XLR connector allows you to connect
a wired microphone (optional) via a standard microphone
cable with a male XLR connector (optional). Since the
microphone INPUT provides 12 V phantom power you can
connect both dynamic and electret or condenser
microphones.
Input sensitivy for nominal level is 2 mV into 1 kΩ.
Pin 1 is ground, pin 2 „hot" (inphase), pin 3 „hot"
(outphase).
(17) Line input (only Direct-Studio)
This balanced female XLR connector allows you to connect
a line audio source via a standard cable with a male XLR
connector (optional).
Input sensitivity for nominal level is 2 mV into 1 kΩ.
Pin 1 is ground, pin 2 „hot" (inphase), pin 3 „hot"
(outphase).
(12) VOLUME
This rotary potentiometer sets the loudness volume of the
microphone / source connected to the INPUT connector
(16) / (17).
(13) Ground/Lift switch
This switch break the link between the amplifier´s circuit
ground and the amplifier chassis.
EQ
The effective two-band equalizer is located in the signal
path immediately ahead of the power amplifier and
therefore acts on both the microphone/line input ch1 and
the line input ch2.
(14) BASS
Rotary control for cutting or boosting the low frequencies.
(15) TREBLE
Rotary control for cutting or boosting the high frequencies.
wireless receiver
(only Direct-Media)
For details on the optional wireless built-in receiver (10)
squelch-control and (11) channel to select the carrier
frequency please refer to the enclosed instruction manual
for the receiver.
9