Hama 00 042558 Bedienungsanleitung Seite 6

Detection Mode Mode Action
A (Highest Auto detection,
Common Lower Standard
Factor Mode) First
B (Priority Port 1-8 detec-
Mode) tion sequence,
First Detect
First Out
HDMI™ 3D video format
• Frame packing: 1920x1080p@23.98/24Hz
• 1280x720p@59. 94/60Hz
• 1280x720p@50Hz
• Side-by-Side (Half): 1920x1080i@59.94/60Hz
• 1920x1080i@50Hz
• Top-and-Bottom: 1920x1080p@23. 98/24Hz
• 1280x720p@59.94/60Hz
• 1280x720p@50Hz
6. Connection and operation
• Connect the HDMI™ Splitter to your devices
• Connect the HDMI™ cable from the HD source to the
input port of HDMI™ Splitter.
• Connect the HDMI™ cables from your displays (monitor
or projector) to the outputs of the HDMI™ Splitter.
• Select one of the detection modes. Please refer to
DETECTION MODE SELECTION above.
• Plug the 5VDC power supply into the HDMI™ Splitter and
turn on the power switch.
• When connections are completed, the HDTV signal will be
distributed to each HDTV display.
7. Trouble shooting
When there is no picture presented, please:
• Make sure the direct connection from the source device to
the display device without the HDMI™ Splitter is working.
• Check all the connection is correct and all connectors are
connected well.
• Check the quality of connected cable, and make sure the
cable does not damage.
• Change the connection sequence of display devices.
6
HDMI Splitter
Suggested Application
TV wall application, sports
bar application, or other
application that different
standard (Resolution,
Color Deep) HDTVs are
connected together.
Home Theater Applica-
tion, or user assigns a
primary sink device by
connect it to port 1.
Source Device
Auto Detection & Auto Adjustment
Supported
The HDMI Splitter will compare
the EDID information of each
sink device (HDTV). A lower
standard sink device will be set
as the primary sink device to
communicate with the source
device.
Detection Sequence starts from
port 1. When connecwt a sink
device to port 1, the device will
be detected. The source device
will set the output signal based
on port 1 (primary sink device).
• Make sure the output resolution setting of source device
can be displayed on all connected display devices.
How to make sure your input and output devices are
suitable with the HDMI™ Splitter?
• Whether all devices are HDCP compliant?
• Whether all HDMI™ cables stay in good quality as well
as connectors?
• Make sure all HD displays support the same resolution
(720p, 1080i, 1080p or 4K2K).
Some of the connected HDTVs show „mode not
support", some HDTVs are working well.
• Make sure all HD displays support the same resolution
(720p, 1080i, 1080p or 4K2K) and color deep (8-bit,
10-bit, 12-bit).
• The HDTVs which show „mode not support" may support
low color deep.
• Try to change the detection mode to Mode A,
• Or set to Mode B and then connect one of the non-work-
ing HDTV to output port 1.
When there is only picture displayed and without sound:
• Check all the connection is correct and all connectors
connect well.
• Check if you connect any DVI interface display device to
the splitter, the splitter may use the EDID information of
the DVI interface display device as communication stand-
ard. DVI supports only video transmission. Please change
the connecting sequence, and reset the HDMI™ Splitter.
Make sure the connection is in the HDMI™ standard.
• Check your cable to see if it supports video transmission
only or it is damaged.
Not Supported
The output reso-
lution and color
deep of the source
device need to be
set first
The output reso-
lution and color
deep of the source
device need to be
set first