Operation With Remote Control - Stage Line FM-200H Bedienungsanleitung

3) Switch on the hazer with the power switch (11). It
GB
will heat up for approximately two minutes. While
the hazer is heating up, the red LED (2) lights up
and haze output is not possible yet.
4) When the hazer has been heated up, the red LED
is extinguished and haze output is possible. From
time to time, the hazer briefly reheats. The red LED
lights up. While reheating, the unit is still able to pro-
duce haze.
5) The haze outlet on the front panel is adjustable:
Release the locking screw (4), adjust the opening
angle and then fasten the screw.
6) After operation, switch off the hazer with the power
switch (11).
Before transporting the unit, it must cool down
and the tank must be completely empty!
Note: Due to residual fluid in the unit, the unit may still emit
some haze after a haze output or after switching off.
6 Operation without Remote Control
For operation without remote control, both the haze
output and the fan power can be adjusted in four
levels with the DIP switches (3).
1) For operation without remote control, set DIP switch
10 to "ON". The green LED (1) lights continuously.
2) Adjust the haze output with the switches 1 to 4 and
the fan power with the switches 6 to 9:
Switch No.
10
9
8
7
6
5
4
3
2
1
100%
75%
50%
25%
100%
75%
50%
25%
Example: Haze output = 50 %
Fan power = 75 %
10
Function if switch set to "ON"
Operation without remote control
100 %
75 %
50 %
25 %
—
100 %
75 %
Haze output
50 %
25 %
fan
haze
output

7 Operation with Remote Control

1) Connect the supplied remote control to the jack
REMOTE CONTROL ONLY (8).
2) Set DIP switch 10 (3) to the left position (OFF). The
green LED (1) starts flashing.
3) Via the magnet on the back of the remote control,
the remote control can be attached to magnetic sur-
faces.
Note: As soon as the green LED (21) of the remote control
lights up, the hazer has been heated up and is ready for use.
7.1 Manual mode
1) For manual haze output, keep the green button
MANUAL (23) pressed: The maximum quantity of
haze is emitted. (However, there is no immediate
haze output. Before haze is emitted, a sufficient
quantity of fog fluid must be pumped to the output
nozzle.)
2) Adjust the fan power with the control FAN (19).
The manual mode takes priority over the continuous
mode and the timer mode, i. e. when the green button
is pressed, the unit always emits the maximum quan-
tity of haze even if one of the other operating modes is
activated.
7.2 Continuous mode
In the continuous mode, haze is emitted continuously.
1) To activate the continuous mode, press the red but-
ton CONT (22) so that it engages and the red LED
(17) above the button lights up.
2) Adjust the haze output with the control OUTPUT
(20) and the fan power with the control FAN (19).
Fan power
3) To deactivate the continuous mode, disengage the
red button.
The continuous mode takes priority over the timer
mode, i. e. when the red button is pressed, the unit is
set to continuous mode even if the timer mode is acti-
vated with the button TIMER (18).
7.3 Timer mode
In the timer mode, haze is automatically emitted in
adjustable intervals of 5 to 140 seconds.
1) To activate the timer mode, press the yellow button
TIMER (18) so that it engages and the yellow LED
(16) above the button lights up.
2) Adjust the haze output with the control OUTPUT
(20) and the fan power with the control FAN (19).
3) Adjust the intervals with the control INTERVAL (15).
4) To deactivate the timer mode, disengage the yellow
button. The LED above the button is extinguished.