Panasonic DMP-BDT100 Bedienungsanleitung Seite 13

Search for access point:
Available Wireless routers (Access points) are searched and
listed. You can select the one to use from the list.
1 Press [3, 4] to select SSID*
(Access point) you want to connect with. Then press
[OPTION] to show information of the selected router,
make a note of the authentication and encryption type.
Access Point Connection Setting
Select an access point to connect with.
To search for access point again, please
select "Search again" below.
SSID
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
SSID :XXXXXXXXXXXXXXX
XXXXXXXXXX
Wireless type :802.11n/g/b (2.4GHz)
XXXXXXXXXX
Authentication type :WPA-PSK
XXXXXXXXXX
XXXXXXXXXX Encryption type :AES
XXXXXXXXXX
Search again
OK
≥ If you can not find the SSID*
2 Press [RETURN] and then press [OK].
Then select an item on the following screen which
corresponds to the authentication type noted down in
step 1 above.
Access Point Connection Setting
Select authentication type.
WPA2-PSK (AES/TKIP)
WPA-PSK (AES/TKIP)
Open/Shared Key (WEP)
Open system
Follow the on-screen instructions to make the settings.
≥ Input your encryption key code in "Encryption Key"
supplied with your Wireless router (Access point).
Wi-Fi Protected Setup-compatible Wireless router (Access point) may
*1
have the mark.
An SSID (Service Set IDentification) is a name used by wireless LAN to
*2
identify a particular network. Transmission is possible if the SSID
matches for both devices.
When you experience
problems with settings
Access Point Connection Setting
Access Point Connection Setting
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point
Connection Setting again ?
Yes
OK
of Wireless router
2
Reception
, select "Search again".
2
No
Display
A conflict with other ≥ Please wait a few moments,
devices occurred.
A time out error ≥ Setting of the Wireless router
occurred.
≥ The signal may be weak. Using
An authentication error
or a time out error
≥ The SSID and the encryption
occurred.
≥ Please wait a few moments,
≥ Connection of Wireless LAN
A device error
occurred.
Network Easy Setting (Connection Test)
Network Easy Setting (Connection Test)
Complete.
1. LAN cable connection : Fail
2. IP address setting : Fail
3. Connection to gateway : Fail
LAN cable is not connected.
Please check the connection.
Select "Yes" and press [OK] to check network
connection again.
Select "No" and press [OK] to finish Network
Easy Setting.
Yes
OK
Display
1. LAN cable connection or
Connection to access point
2. IP address setting
3. Connection to gateway
1. LAN cable connection or
Connection to access point
2. IP address setting
3. Connection to gateway
1. LAN cable connection or
Connection to access point
2. IP address setting
3. Connection to gateway
1. LAN cable connection or
Connection to access point
2. IP address setting
3. Connection to gateway
Check the following
and then try again.
(Access point) for MAC Address
etc.
the USB extension cable
supplied with the Wireless LAN
Adaptor, adjust the position of
the Wireless LAN Adaptor.
key of the Wireless router
(Access point).
and then try again.
Adaptor
If there is no improvement in
symptom, consult your dealer.
No
Check the
following
≥ Connection
:Fail
of the LAN
cables
:Fail
( 11)
:Fail
≥ Connection
:Pass
and settings
of the hub
:Fail
and router
≥ Settings of
:Fail
"IP Address /
DNS
:Pass
Settings"
( 31)
:Home
network
available
:Fail
:Pass
:Pass
:Fail
(13)
VQT2U34
13